Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 4 at 11:59pm EST.
Whirlpool Washer Bearings
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Whirlpool Washer Bearings
Whirlpool Washer Tub Seal and Bearing Kit
PartSelect Number PS3503261
Manufacturer Part Number W10435302
This kit includes the shaft, 3 bearings, seals , grease, adhesive and the spanner nut, which is NOT sold separately. Also may require a bearing driver tool to install. PS3503307
Fixes these symptoms
- Leaking
- Noisy and Marks Left on Clothes
- See more...
Installation Instructions
DENNIS from OELWEIN, IA
Washer was noisy, Top seal and bearing bad
You better be confident in your repair abilities before you try this. Get the washer to a large open area, like your garage, because there are a lot of parts. Take off the back, pop the top, unsnap and remove the top ring off outer tub, take out the agitator, take out the inner tub, disconnect the pumps and electrical wires, take screw out of rotor on bottom and remove rotor, take out 4 bolts to remove motor magnet ring, and now you may be ready to unhook the outer tub from the 4 supports (springs) and lift it out of the metal frame. Then unscrew the bottom nut on the shaft, use blocks to hold the tub in place, and carefully tap the old shaft and bearings out. The instructions that came with the kit helped. The shaft and top seal comes out the top first. Then you can tap out upper bearing and then the lower bearing and spacers.Instructions called for a special tool to install the bearings but you can carefully tap them in. You will need blocks to support the tub while you tap them. First block under the tub and install top bearing, then flip over and use several blocks to hold tub while you drop the shaft, spacers, and tap lower bearing in. I did not need to tap on the inner ring of the bearings, just the outer ring. Be very careful not to damage the seal in the bearings. That's why you must tap them in careful and slow. Them install the nut on the bottom. You need to hold the shaft with damaging it while you tighten the nut. I used the hard nylon gear from the inner tub which I was replacing with a new one. Then put it all back together.
Read more...
Whirlpool Washer Centerpost Bearing and Seal Assembly
PartSelect Number PS334447
Manufacturer Part Number 285203
This assembly comes with one transmission stem seal, two center post bearings, and three agitator shaft seals.
Fixes these symptoms
- Leaking
- See more...
Whirlpool Washer Spin Tube Bearing
PartSelect Number PS11746369
Manufacturer Part Number WP8546462
This spin tube T-Bearing is an inch long. Sold individually.
Related Whirlpool Washer Parts
- All Whirlpool Washer parts
- Whirlpool Washer Agitators
- Whirlpool Washer Belts
- Whirlpool Washer Brackets and Flanges
- Whirlpool Washer Caps and Lids
- Whirlpool Washer Circuit Boards and Touch Pads
- Whirlpool Washer Dispensers
- Whirlpool Washer Doors
- Whirlpool Washer Drawers and Glides
- Whirlpool Washer Drums and Tubs
- Whirlpool Washer Filters
- Whirlpool Washer Handles
- Whirlpool Washer Hardware
- Whirlpool Washer Hinges
- Whirlpool Washer Hoses and Tubes
- Whirlpool Washer Knobs
- Whirlpool Washer Latches
- Whirlpool Washer Legs and Feet
- Whirlpool Washer Motors
- Whirlpool Washer Panels
- Whirlpool Washer Pumps
- Whirlpool Washer Seals and Gaskets
- Whirlpool Washer Springs and Shock Absorbers
- Whirlpool Washer Switches
- Whirlpool Washer Timers
- Whirlpool Washer Transmissions and Clutches
- Whirlpool Washer Valves
- Whirlpool Washer Wire Plugs and Connectors