Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
icemaker stripper fall a part
instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull" Dremel and it works!The instalation part of the "job" was less then 10 min.
The water dispenser on my GE refrig started leaking for about 5 seconds after release of the switch. I replaced the filter and the combination ice/water solenoids. Though this did not solve my problem I did troubleshoot more. I located the water reservoir behind the vegetable drawer. The reservoir mount had broken off. The reservoir had flipped so the water connection was no longer at the top. This was the cause for the continual leak. After mounting the reservoir correctly, the water leak stopped.
Ice maker arm disconnected from frame causing problems.
The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.
Unplugged electrical and turned off water at source. Removed back cover of refrigerator. Removed one bracket screw holding water valve. Pulled element out six to nine inches and disconnected water line to the unit. Removed electrical and water lines from old valve. Marked each line for easy reassembly of new valve. Turned water back on and tested for leaks. The whole process was very easy. Service from PartSelect .com was very good.
Icemaker waterline leaking inside by the grommet where the water line comes in the refrigerator . First removed the water line from grommet . Then removed grommet by hand from the fridge. Last, reversed prodedure.
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
I removed the nuts holding the cover to the back of the refrigerator. I removed the main water line to the part. I then removed the nut holding the old water and valve bracket assembly to the refrigerator. I removed the wiring harness from the old part and attached it to the new one. I pressed down on the release to the hoses, pulled them out, and reattached them to the new part. I reattached the part to the refrigerator. I reattached the main water line back to the part. I reattached the cover to the back of the fridge. I tested the icemaker and water dispenser--and everything worked fine. And, the best thing was, there was no puddle of water at my feet! Such an easy fix!
The defective solenoid assembly was removed from the refrigerator and the electrical connection was unplugged. The new assembly was placed beside the defective part so the wiring harness could be removed and installed on the new assembly. I had to use a flat screwdriver to loosen the connectors. The water connections were then carefully moved, one at a time, to the new valve. The water was then turned on to check for leaks. There were none so the assembly was installed in the refrigerator and the back cover was screwed into place.
The part was shipped on a Monday and I received it at noon the following Tuesday, using the least expensive shipping method!
Remove ice maker out of fridge; remove 3 screws replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"
Water leaking and freezing everywhere. Weird shaped ice cubes, more like chunks which jambed the dispenser.
First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic door jamb putting the new unit in but other than that all is well and functioning well.
I started by shutting off the water inlet valve and then unplugged the refrgerator. I then disconnected the tubing leading into the solnoid. Removed the old solenoid, replaced it with the new part reconnectted the tubing and gave it a test run. After about 2 hours we had ice being made again! I then reconnected the bracket to the refrigerator and haven't had a problem since.
Did the repair just as the instruction said, once I read it. The part I didn't read was that if the plug was under the ice maker, you had to take the wire out of the clip on the side. So, had to dismount ice maker, unclip wire, remount maker, plug it in. Still under 30 minutes. Thank you.
I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
