1. Didn't understand how to do continuity test for 3-wire door switch. After looking that up, I discovered that wasn't the problem ! I have tested, the thermal fuse, oscillating fuse,start switch, I've tested the timer and the black , blue connections go to zero ( continuity good) the tan , white connections just barely off of infinity. I've ordered a new timer. I'll let you know if that's the problem. If you can more diagnostic videos. AKH
Removed old door switch and tested with ohms meter. It registered as charged, but when black button was pushed it did not cut off (go to zero). Replaced the part just like the video showed. Only problem i had was dropping my screwdriver down into the dryer well. It was doing no harm so i left it there since i tried retrieving from the back but was not able to get entire back off!
I removed the two screws underneath the lent trap the removed the two screws that held the dryer switch assembly. I then lifted up the top and disconnected the door switch assembly. Removing the door switch assembly was the toughest part, and it was not difficult. Simply grab a pair of pliers and pull. I the attatched the new door switch assembly and the four screws and my dryerwas as good as new. I paid around $20.00 including shipping and saved myself a couple of hundred dollars
Determined that the door switch was not making contact. Removed the lint screen, removed two screws in the lint screen housing, pulled the top of the dryer up at the front of the dryer. This provided access to the door switch which was mounted on top.
Dryer would not do anything but the inside light was unusually bright.
The brightness of the light was because the door switch was allowing too much current to the light bulb when the door was open but the switch would not swich the current to the dryer motor when the door was closed. After a day or so of this bright light it burned out. I removed the two screws on top that hold the lint trap in place then I could access the switch by sliding the top of the dryer forward and lifting the it as you would lift the hood of a car. The switch is on the right side and plugs into a three wire connector and only fits in one way. Cheap and easy fix after unplugging the dryer from the wall power outlet.
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
I had a dryer that wouldn't stop when the door was opened and it was a danger to my young kids.
After getting the part and sizing up what to do. I removed the 6 1/4 hex nuts from the back. I removed the 2 hinge nuts 3/8 and popped the lid of the dryer up. It wasn't coming up all the way. I removed the lint filter and removed the two #1 Phillips screws that held the lid to the duct and it came up easy.The switch itself was clipped together and came apart with ease. 2 #1 Phillips screws held the switch in place and quickly tightened down the new switch. I clipped the new switch to the old lead and just reversed the order putting it back together. The light worked and the drum stopped when the door was opened during the cycle. The part matched perfectly and there was no guess work about clearance. It was an easy repair.
Door switch had broken off and interior bulb not working
I first checked the owner's manual an on line documentation from the manufacturer on how to change the door switch on the dryer but found nothing. First step: Turn off breaker to dryer. I then popped the lid of the dryer and could see that the switch was accessible from the top. I was pleasantly surprised to see the parts arrive within 2 days with the lowest cost standard shipment. I loosened the 2 screws holding the switch, unplugged the modular clip, replaced switch, resecured with screws and dropped dryer lid back in place. Interior bulb was busted up, I removed cover plate, base and broken glass, seated replacement bulb, reattached cover and turned breaker back on. Dryer switch and bulb are working again. You sent me exactly what I needed and fast. Thanks for the quick turn around!
After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!
discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
