Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Electric burner element not working
Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair
1st gen whirlpool Duet dryer sensor not working in automatic cycle. After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.
Turn off power to the stove (unplug or turn off breaker) Remove back panel screws (Phillips) and back panel Unplug switch Remove knob and attaching screws (Phillips) Remove and replace switch Reinstall screws for switch and plugs in the back Snap off the end of the stem if it's too long and reinstall knob Reinstall back panel and turn power back on
*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*
I shut off the breaker to the stove. I removed 2 screws from the underside of the cooktop at the front of the unit. I raised the cooktop and had my helper hold the top at an angle to access the burner. I removed 2 screws attached to the burner and then loosened the 2 clips and moved them to release the burner. I transferred the electrical connections from the old to the new. Reinstalled the burner and cooktop. Turned the breaker on, tested the new burner and I was fone
Ordered new element from PartSelect. It arrived shortly. It did not match the original. Guy at appliance store explained how I could connect the wires on the new one. It still did not fix the problem. A repair man tried for 2.5 hours to fix it with no success. Now I will return the replacement element in the return envelope provided.
I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
1) Remove power from range. 2) Carefully unsnap and pull out the old switch. 3) Remove wires using pliers. 4) Attach wires to new switch. 5) Snap in new switch.
Taking off the glass lense for the light bulb was harder than I thought. It unscrews counterclockwise, but it was very hard to get off. It would not turn. I ended up using connector pliers I use for work, that has rubber jaws. The lense unscrewed very easy with it. Light also unscrews out. PartSelect.com is the only way to go to buy parts for appliances. It is simple, even has the illustrated parts catalog. And it saves a lot of time and gas, driving around looking for the part!!. PartSelect came through again.
Removed 3 screws holding the glass door bracket. Placed glass into door holders, had another person hold glass while I replaced the removable bracket screws.
The side trim on the glass door needed to be replaced.
After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.