Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer was noisey for about 2 years. Repeated greasing of the wheels only resulted in it squeeling again after 6 months or so
Finally got tired to greasing the wheels only to have to do it again so I sprung for new wheels and shafts. Popped the top open, removed the drum, installed the two new shafts with supplied screws then attached the wheels. Figured I'd change out the original belt while I was at it even though the old one still looked good. It's nice and quiet again, plus it give me a chance to clean it out.
I popped the top off and tipped the dry over . It took 2 to reposition the drum and belt back after taking it out and remving the old wheel and replacing it.
Had to disassemble most of the dryer including pulling dryer drum in order to get to drum support rollers. Not a real difficult repair, just time consumming because of amount of parts needing to be removed inorder to get to rollers.
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken belt
Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.
Very simple-remove 3 screws that hold the Control Panel on, remove the two connectors and replace with new part in reverse order. Unfortunately, this did not fix the problem. Will be ordering complete timer assembly.
googled"dryer not heating". landed on partsselect.com. checked parts like website said with multimeter. pointed to thermostat. ordered it, replaced it, it works now.
My part came a day or so after the order was placed. There was really no installation required, but I will definitly make orders from this site again. Thank you very much!
Once we realized we needed to take the FRONT off the dryer, not the back all went well. It was an easy fix and the part fix perfectly. Instead of $60 or more for a repairman, we spent less than $20 fixing the dryer.
First I removed the screws of the dryer cover. Next removed the screws holding the dryer drum.
Drilled out the two rivets left from the old glide. Inserted the plastic and postitioned the cushion underneath. Inserted the new glide and drilled a hole in the plastic to accomodate the new rivet. Inserted rivet. Pulled the other end so it was tight holding the cushion and did the other end. Done.
Had to cut the glide 1/4 '' of the width to slide it through the existing slots in the panel.
Unplug - use screwdriver to release top latches. Raise top to more than 90 degrees - hard on hands or head if it falls. Remove wires from door swithch and remove front panel screws, lift off front cover. Remove screws from front paned of blower housing. Remove snap ring - shaft clamp already loose, remove old blower whee and install new one. Use DEEP(spark plug) socket tap new wheel onto shaft, replace clamp and snapring and reinstall panel on housing, put front panel back-install door switch wires before screws, replace top, plug in and test run.(note 1st word correction)
Dryer smelled like something was burning, then would not turn on.
This is the second time that this has happened with my dryer. The first time I replaced the thermostat and fuse, and it worked for a few years. This time I replaced the element and thermostat at first. Still nothing, then got the fuse; and walla just like new. Of course I lost a screw somewhere down at the bottom of the dryer, so there is only one holding the thermostat in place. Also I took off the front and cleaned out the lint traps; both times it was loaded with crap. Probably why it stopped in the first place.
Easy repair and I am not the handyman type. Unplug the unit. Lift the top. Remove 2 wires from temperature sensor and remove single screw to lift out the plate the sensor is mounted to(Easier to change the sensor out this way). Remove 2 wires from heating element and then remove single screw. Lift out heating element and replace with new one. Screw back in and reattach 2 wires. Remove 2 screws on the plate for the temeperature sensor and replace with the new sensor. Once 2 screws are back in the plate holding the sensor, screw back in with single screw and attach 2 wires. I called a tech and they wanted $125 just to look at the unit. When I read other reviews of how easy this repair was, I thought it was worth a try. Definitely saved us a bunch of money and time.
1.Removed retaining clips,washers,spacer,and cylinder rollers 2.Removed and replaced support assembly 3.Installed spacer 4.Installed cylinder roller assembly 5.Installed washers and retaining clips This is my second time ordering parts from PartSelect and I am amazed how fast I recieve my orders, which minimizes the downtime of an appliance that's frequently used.
I took the front off the cabinet (pry up front of top and remove two screws. Removed the drum, replaced the left rear drum support roller by removing one snap ring on shaft of roller and repacing after installing the new wheel. Reinstalled the drum, the hardest part of the repair was getting the belt back on the drum. It is hard to reach the belt to place it back on the motor. (small space to reach through) Being able to purchase a single wheel from this website saved me $50.00, the local suppier wanted to sell me a whole kit.