Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Noise when running and motor stop. Motor bearing overheated.
Unplug dryer
Pick the top up at the front and swing up. Inside each side of the front is a screw to remove. Do not forget to unhook the door switch wires. Pull the drum. Push belt off as you remove the drum. Works better to reach in at the lower right and take the belt off of the tighener first.
After you clean out any lint in area unplug the wires from the motor and snap off the hold down clamp on the back bearing.
The blower needs to be released fromt he shaft. The snap ring in front of the blower needs to be taken off. This can be done with a screw driver by prying off the flat spot on the shaft. However, a snap ring pliers would be better. The front of the blower housing must come off as the blower must come off. There is a snap ring behind the blower that must come off also.
The biggest problem I had was removing the front motor bearing housing from the plastic blower housing. It is easy once you see that the front bearing housing is held in by four tabs in the plastic housing. By rotating the front bearing housing 90 degrees you will be able to pull it out.
From there just reverse your action. The belt went on ok. I found by putinng the belt on the drum and the motor drive pully first I was able to reach in an put the belt over the tighener.
First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--
my ex husband took the top and front of dryer off and removed the drum and belt. he pulled off the worn roller and replaced it with the new one. we put the drum in backwards and had to turn it around but all went well and the dryer is quiet again!!!
I opened the top then i did change the heater element kit only one screw out and finaly replace the temperature switch, again one screw out was realy ease was my first time,the professional online help my, every one can do it thanks i appreciate your help.H.E.K.P/N AH2162280 - temp/switch p/n 31001449.
popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale
I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit. OK, so much for the intro.
I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.
She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.
When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer. Thank you so very much. Dr Robert E McGinnis
I suspected (correctly) that the thermostat was malfunctioning so I ordered the Heating Element Kit. This repair would have taken less than 15 minutes if I would not have dropped one of the sheet metals screws in the back of the dryer when re-installing the heating element.
Took off top and front. Removed belt and pulled drum straight out. Unclipped the rollers. And noticed the rod that holds the roller was worn out badly. Good thing I bought the kit. Because it came with everything needed and was cheaper then buying the rollers seperate. Only hard part was putting the new mounting on for the rod. They are not predrilled. So does take some force. Put everything back togetther and dryer is working like new. fyi you can also clean out your air duct of lint buildup when doing this project. Had a repair man come over 2x in past year and each time he would replace the roller and charge me $150 each time. I spent $300 on that bozo. When i could have ordered the parts myself for a fraction of the cost. This was well worth and easy to do.
Using a flat-head screw driver, I removed the 1 screw from the small "door" on the back, upper right corner. Once the screw was removed, it allowed the door plate to "pop" open; exposing the old bulb. I removed the old bulb; replaced it with the new one. DONE!
I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!
Overall an easy repair. Belt came with diagram for easy threading the belt.
removed screws on back plare and replaced heater element. Thank you very much foe your quick delivery of the part I ordered. I was reall;y schocked to see how fast the part arrived. I will recommend your site to anyone who needs parts like I did,. Thany you Very Much, Alan Brooks
Lifted hood ,and took two screws and tilted the front back and remove the door switch , and took front off ,use little socket set, took cover off fan housing took pliers removed clamp on fan , remove key way on end ,slid fan off and put new one on and reverse the way if came off.