Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
My washer started leaking water out of the bottom.
I pushed a small screwdriver under the top lid and pulled the front out and lifted it out or the way. The rubber hose had two clamps holding it. One you loosen with a flat screwdriver and the other one you squeeze with pliers to remove hose.Then replace hose and put front back on. It's very simple.
The agitator coupling in my washer was stripped out.
I had already removed the old coupling by removing pulling the agitator straight up off the coupling, then I removed the bolt that held the coupling in, and pulled the coupling up off the shaft. I placed the new coupling on the shaft and pushed it down until it seated, put in the new bolt that came with the coupling, replaced the agitator, and was washing clothes within 10 minutes. On time delivery, right part, complete with instructions. Good job.
Motor/pump was clogged with foreign material. Belt was just replaced because that's how I do things....
First the front cover of the washer just peeled off and everything was right there. Slid the clamps back, took the screws and while pump was out, I replaced existing belt with new one. After new belt was in place with proper tension, I fitted the new pump assembly in place. Piece of Cake !!
figerout how to take the old one off that was a little hard to do but did it. got the socket set to get the middle undone. clean to out and put the new one in and it works just fine and better then ever.
I watched the video and disassembled the machine pretty much the way the video showed. There were a few differences but nothing big. The noise sounded like a dry bearing but wasn't sure where it was. Read the responses and it said it was the tub bearing washer. It made some sense if it was metal on metal. It was a dry bearing (should have listened to my common sense, but these guys know more than I do when it comes to washer repair) on the transmission that had been ruined because of a leaky tub seal, which I also replaced. The transmission was not available at the time of repair (but is now) but that kind of investment may be better in a new unit. There is a video on YouTube that shows you how to replace the bearing, BUT it requires someone with some mechanical knowledge. I'll try it later in the year and if it doesn't work we'll have to purchase a new unit.
I had to replace the water fill nozzle on my GE washer, and having the instruction video on the parts page is a real time-saver. It shows how to remove each part on your washer in order to access the area where the part needs to be replaced. Start to finish, about 20 minutes. Easy peasy.
Water dripping into the washer when washer was not in use
I followed instructional video on partselect.com, it was very easy, but it didn't take care of the problem. I got to to order "TRIPLE WATER VALVE" and that did the trick. After opening the washer first time (for water fill nozzle), it took me even less time. You don't have to take the front panel off to replace the water valve.
REMOVED THE AGITATOR BY LIFTING STRAIGHT UP WITH MY HANDS. COULDN'T REMOVE THE COUPLING WITH THE NUTDRIVER AT FIRST, DUE TO RUST. SPRAYED A LITTLE WD40. LET IT SET FOR FIVE MINUTES AND REMOVED THE SCREW VERY EASY WITH THE PLIERS. TOOK OUT THE OLD COUPLING AND REPLACED IT WITH THE NEW ONE. THANKS FOR THE YOU-TUBE INFO.
Small wire had tried spin out of drain pump. Wore pin hole in the rubber drain hose....
Unplugged...Removed back from washer...Using nut driver-cordless drill...Inspected hose-found leak....Removed hose with pliers & screw driver.....Than dried the hose...& than for temporary fix (for the wife to continue washing) used some Epoxy for rubber.....Than ordered new part. Received and reinstalled replacement. Thank you
The front panel has to be taken off to access the washing machine pump. To do this I used a putty knife I inserted the putty knife in the slot at the top of the front panel where it meets the top of the machine to release the clip that holds the panel in place. Once the panel is off the pump is mounted to the bottom of the machine with two screws. There are also two hoses attached to the pump that need to be taken off. Before you do this you have to get as much water out of the machine as you can to minimize the amount of water that will come out when you disconnect the hoses. My recommendation is to replace the spring type hose clamps the manufacturer uses with a screw type hose clamp. These are much easier to put back on once the hoses are in place. You are not fighting the spring clamp while trying to put the hose on in a confined space. Then put the front panel back on. This may take about a half hour if you do not have too much clean up because you didn’t get enough water out of the machine.
The agitator "wings" are open at the bottom so any clothes with strings gets caught in these wings and eventually brake the wings off.
I watched the video provided by your site and followed it. I removed the clothes softener part from the agitator, Got a good grip on the agitator and pulled up. It came right off. Aligned the new agitator groves and slid it into place, put the fabric softener part back on! Super easy.
Reach down and grab the base of the agitator with both hands and yank up with slightly more pressure on the left or right, whichever side you prefer. This will break loose the holding clamps/pull straight up. To re-install: align slots and push down until it snaps. Simple as that.
