Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer was stopping during the spin cycle and making a grinding noise.
Our Samsung HE washer started making a grinding noise and stopping at the end of the rinse/spin cycle. I had replaced the clutch and seal 2 years ago and it sounded like it was going out again, however we were not getting the gunk inside the tub like before (seal) and the machine was throwing the tE error code when it stopped which it did not do last time. According to the manual this meant a thermistor error and the solution was "Call for Service". The machine is 9 years old and way out of warranty so....uh No! I ordered the new thermistor for $15 plus shipping to correct the tE code before looking to replace the clutch again or get a new machine. The new thermistor arrived, leaned the machine on its back, unplug one connector, remove two screws and pull the old one out of it's hole, push the new one in, replace two screws and the connector and GO! Problem fixed! No tE code, no stopping, no grinding noise. As best I can tell, the old thermistor was faulting during the spin cycle and the machine went into emergency stop mode which made the grinding noise. It was not the clutch or bearing at all. Most of the repair time was moving the machine out and disconnecting lines so I could lean it onto its back. Note: If your machine is stopping before draining, it will have water inside the tub which will drain out of the hole where the thermistor goes when you pull the old one out. It has an o-ring to seal it, so just expect a little water to come out and be ready to catch all the water or put the new one in quickly.
Coupling and coupling assembly was broken along with stator coil being cut at 2 location
I first fixed the stator coil by repairing the cut coil spots at 2 location using solder and with a bit of equivalent wires to extend with heat shrink sleeving to extend over the iron core. Next, I assembled the new coupling in the new coupling assembly with a bit grease around cogs. Wached few videos to see orientation since mine was broken assembly and wasn't certain how it sits inside. Once oriented and seated right, I wiggled to sit in properly over the stator cog..I felt the stator cogs with coupling locked to the shaft. After that I secured the main nut and connected the appliance. All worked perfectly after that. Thanks for sending the ordered parts. Now the washing machine is strong and solid in its agitation.
washer making noise when washing. rinse and spin was normal.
Everthing went to plan except the wet side of the parts removal was difficult. used puller to remove the wash plate and got it to release. But the plastic part of the wash plate released and left the aluminum part still on the coupling. Corrision was the problem, and I had to again use a puller to remove this part of the wash plate. So it wasn't a matter of just lifting the wash plate off by hand. The rest of the replacement was fine.
Move the washer to the garage and laid it on its side. Remove the large nut from the center shaft using a crescent wrench. Tap the wrench with a hammer until the nut comes loose. Next you'll need a puller to remove the part that was secured by the nut. Mine would not come off by hand. Next remove the three screws securing the white plastic components to the bottom of the washer. Remove the two plastic pieces and throw them in the trash because I'm sure they're garbage. Reverse the process for installation and reinstall the washer. Put some clothes in for the test wash and the washer should be silent. Two different appliance repair folks gave me estimates that were higher than the cost of replacement. I got out from under this fix for around a hundred bucks. It was worth every minute of my time. Good luck.
Washer pulsator was coming loose during wash cycle.
Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.