Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
washer stopped spinning
I noticed the belt was off, first, then pulled it back on. Washer worked, but very noisily, as belt continued slippage. I bought new belt after reading how to repair, then when it arrived, I read how someone installed it without having to remove bolt, etc. I tried and succeeded. It agitates just fine, but stalls when spinning. It's like the belt is too tight, now. i am gonna try rotating the rotating parts to see if that will help loosen it.
Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry to wash :-)
Took complete tub assembly out of washer and inspected it. Did not find an obvious cause of leak but all 8 screws on inner tub hub were loose. As both tub nut and split ring were corroded, replaced them and the outer tub seal. Did a lot of cleaning!! As I was putting the trans assy back on the outer tub, I noticed a crack around the drain spout. At 1st, it looked like it belonged there but a closer look proved it didn't. I ordered a new outer tub (which came in 2 days) and I put the whole thing back together. Reassembly was far easier than disassembly was and I learned a whole lot about washers. YouTube is a great source of information.
Placed a small rope under the agitator and pulled up with a sudden jerk . It popped right up and out . I removed the bolt holding the coupling .I then removed old coupling and replaced with new coupling and bolt. I then installed new agitator pushing down until it clicked into place . All done , less than 15 minutes . Thanks to others that gave their feedback so we could learn what to do .
Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.
Took about 10 Minutes to have my washer up and running again. So easy, and I almost bought a new washer! Fixed it before my husband got home from work. Thank you PartSelect!
Tub made banging noise when stopping from spin cycle
I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.
Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.
First I removed the front panel using the screw driver. I removed the old belt which was in the bottom of the washer. I placed the new belt on the motor and adjusted the pullies. I replaced the front panel. The washer spins much better now than it had for the past year.
Washing machine would stop at spin cycle and just continuing spinning
Unplugged the Washer. Removed the plastic clip that holds the selector knob to the stem on the front panel. Remove the knob and the plastic plate behind it (It is keyed, so you can't put it back on the wrong way.) Removed the four (4) Torx screws from the top of the front panel. Tilt the panel forward and there is one (1) screw that holds the cycle timer to the inside front of the panel. Use a nut driver to remove that screw. Disconnect the Large multiconnector plug from the timer assembly and slide the entire timer assembly out. Slide the new assembly in, put the the screw back in and reconnect the plug assembly. Tilt the front panel back into osition and replace the four (4) torx screws in the top of the panel. Place the Plastic plate back on the stem and push the knob back on, positioning it to line up with the arrow on the back plate. Plug the washer back in to the electrical outlet and the job is done.
washer had heavy wet clothes left after spin cycle
The trick is to pull the front cover off by using a putty knife .slide it under the cover at both front corners.it will click on each corner.then pull front cover off .lift off the bottom catch hooks.look for the pump on the bottom right side.unplug the wite connector .take 2-5/16 bolts out holding the bracket.then grab a pliers .squeeze the hose clamps and pull the 2 hoses off.assemble new pump.
Washer did not drain completely with water on floor, drain pump frozen.
After unplugging the washer, I drained remaining water from washer tub using my Wet/Dry vac. Ordered new pump Sunday night from PartSelect, 'Standard delivery', part arrived Tuesday morning. Removal & installation took less than 20 minutes.
took off front control panel, searched the internet for reasons for my problem, replaced the pressure switch, did not fox my problem, replaced the intake valve which fixed the problem.
Use paint scraper to release spring tabs holding front cover on.
Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.
R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).