Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Tranny oil ran out onto Laundry room floor/making noise
Removed front cover(use screwdriver)clips on top of cover under lid Disconnected power from wall Disconnected wires to motor 1 screw/unplug for motor Uncwrewed clamp on drain hose Removed top lifts off easliy With help released Washing drum assy from hangers Slid back and Tilted drum assy outwards from drum opening out to the front of machine Pulled agatator up and off of hub Remove one bolt from hub 1/4 " rachet w 3/8" socket Pull off cap Removed Locking nut(couterclockwise)nut is soft metal used good vice grips firmly locked on nut Removed inner washing drum Turned over Entire Assy (motor up) Removed belt (slid off) Removed 4 blots from Motor/Tranny assy to Plastic outer drum Lifted off Motor/Tranny assy and pulled tranny out Reaasemble in reverse order witht the exception of replacing the hub seal(inside)Outer drum assy. There were service instruction under the front control panel.
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
13 of 15 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two paddles on the agitator broke off.
After reading how others have done this and how easy it was, I decided to give it a try. And, sure enough, it was really easy. However, one concern I had was on lifting the old agitator off from the axle using both hands. I didn't want to have the agitator come crashing into my face as I pulled up. So I put a pillow on top of the agitator.
Noticed 3 straps were broken when we replaced the hose
I removed the front cover, then unscrewed the top to expose the top. There are two screws that hold each strap, which turns out are different sizes, so I had to use two different sockets. I also had to remove the hose & plastic tube for the bleach. Once that was done, the replacement was easy, I replaced all 4 straps, reconnected the tube for the bleach, screwed the top back on and snapped the front cover into place. This took maybe 30 minutes - and I am female!
Left up agitator, use socket set to remove agitator coupling. Then replace old agitator coupling with the new one. Tighten nut with socket set, replace agitator. Yes it is that easy.
Tipped washer over on to the front side. Removed back panel. Removed the flex coupling to the water pump. Removed the old belt. Installed the new belt and reversed the process to put components back together.
Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.
The zinc drive hub that connects the transmission to the tub had corroded away.
It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
10 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer won't drain water
Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.
Removed the front panel with a stiff putty knife, removed the worn belt. Placed the new belt on the front pully and than the rear pully, turning clockwise. After checking the spin cycle I put the front panel back on and I was done.
removed washer front panel, top panel to access the water fill spout and hose. Disconnected and replaced. personnel at part select were very knowledgable about detailed part and the overnight service was right on time. I would recommend part select for your next appliance parts needs.
Open back cover and found that drain pump had a bad seal. Took it apart and bought new seal some what same size. Put everything togather and start washing clothers and wife complained that it became wost the before. When on line and found pump and price was just right to take a risk. Ordered on sunday and got ups tuesday. Replaced pump on Sunday and leak was gone and wife was happy.
------Got chicken and beer that Sunday--------------
First I pulled off the front panel using a flat blade screwdriver to get it started. Then I could watch what happening as I tried starting the washer. When I put the dial to the Rinse Cycle and pulled the dial to start the washer, it would start to run for about 5 seconds and then stop. I tried this several times and the same thing happened. I noticed the water pump located in the front lower right hand corner was not running. It would only hum. I drained the tub by holding the wash machine drain hose into a bucket. If I held the hose down toward the floor, the water would flow freely out of the hose and into my bucket. As the bucket filled up I just raised the hose, emptied the bucket and repeated the process until the tub was empty. Sure saved time over trying to empty the tub by bailing the water out with a can. After the tub was drained I removed the two hoses from the pump and then the two mounting bolts and the pump was out. I bench checked the pump with an electric cord and it stilled just hummed. I knew for sure then the pump was bad.
I then ordered a new pump from PartsSelect.com. I entered my wash machine model number and PartsSelect gave me a picture of the replacement pump. I was a little worried that it did not look the same as my old pump but I ordered it any how. The night I got the pump I installed it in about 30 minutes. No problems, it just worked like a charm. Thank you PartsSelect.com I will definitely use you for all my appliance repairs in the future. I know there will be more.