Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
w/d repeatedly fills with water during warm or hot loads
E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.
I followed various tube videos. The vides were very easy to follow. But the most important thing to have to do the job is washing machine spring removal tool. This tool I had to order it online unable to locate in store.
First unplug the machine. Turn the water off to the hoses. Remove the hoses from the machine to make it easier. Remove the screws from the back of the top cover. Pry the front sides with a screwdriver and lift. Standing behind the machine on the left side you’ll see the three solenoids or inlet assembly. Remove the two screws so as to take the inlet assembly out. There are hoses attached to the assembly.
The web interface is nice, however in this situation it references the wrong part which was not known until the item arrived. Customer Service handled return, however I had to call LG directly to confirm correct part number (LG p/n 4866ER0004A = p/n PS3524040) but this was only after LG also gave wrong p/n. When replacement part arrived the internal concrete had a crack in it. The part is basically a plastic shell that is filled with concrete. However the opening (about 1 x 4) is left open and with the concrete having a crack in it the piece will vibrate together and continue to break down over time (which is what happened to the original one) Before installing I chose to fill opening with epoxy and a plastic layer, then covered with electrical tape to seal it in. I feel this item is poorly designed from LG. Additionally this item was poorly packaged by PS when shipping which caused the damage (it weights about 15 lbs and was allowed to float around in a large over-sized box filled with large air pillows). I have photos but no way to upload here.
-Unplug washer -Turn off water supply -Pull machine away from wall -Remove two screws on the back holding the top panel in place -Slide top panel toward the back and remove -Unplug electrical conectors to the control panel, remove screws and take out panel. -Remove lint trap plastic door cover bottom front left and screw holding plastic housing. -Take housing out. -Remove screw that is behind plastic panel holding front panel. -Using spanner, release spring clamp holding gasket to the front panel. -Remove top screws holding front panel on and take off panel. -Remove hose clamp and hose at bottom of gasket. -Release inner spring clamp on gasket to washer drum and take out gasket. -Install new gasket and spring clap to drum. -Reverse the order to reassemble.
The pump filter leaked after cleaning it out. Would work with teflon tape, but wanted to see if a new part would eliminate the need to wrap it every time.
Unscrewed the old part; screwed in the new part and said a quick prayer - LOL! The part worked great, but I wanted to mention how quickly I received the part! I would definitely order from this company again!
bought a position sensor top load machine when i tipped the machine over i found the nut and washer on the floor .replaced the sensor and nut took about half an hour
Loud grinding noise, especially during the spin cycle.
First I watched several videos on YouTube, numerous times. When I started to disassemble the washer, I put the parts I removed on the floor in the work area in the order I removed them. I also took a couple of photos of where wiring and hoses went so I would have a reference the next day (I took parts of two days to complete the repair).When I removed fasteners (screws, etc), I labeled them as to what part they went with, making re-assembly easier and faster. The most difficult part was re-installing the wire retainers on the door bellows (make sure you use some liquid dish detergent as lubricant). The results were great, I have a like "new"washer now.
Water was collecting in the machine after it finished its cycle.
Turned off hot and cold water supply. Pulled out machine and disconnected hoses, unplugged power.
Unscrewed 4 screws at back top of machine (holding plastic bracket to cover). Pulled out trays from front where detergent is poured, and removed small screws under trays.
Slid cover back and up. This was the only tricky part. There are pegs that must line up with large holes in cover before you can easily lift cover up. Helps to look from underneath and find pegs on each side.
Using pliers, fully open clamps holding hoses to the inlet valves, and carefully pull off hoses while keeping clamps open with pliers… making sure to keep track of which hose goes to each motor. Take a picture of electrical connectors noting color and sequence of connectors on each inlet valve motor. Pull all connectors off.
Unscrew screws holding each inlet valve to machine. Put new inlet valves in place of old, and screw in place. Reconnect hoses (using pliers to hold open clamps, then slide clamps over tubing and inlet valve connector). Reconnect electrical connectors carefulljng lining up colors of wires and sequence using picture taken in previous step.
Replace cover. Screw all screws back to secure cover. Replace trays.
No power to dishwasher. Confirmed that outlet had power coming out.
Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upside down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.