Remove aggitator, disconect 4 support straps, pry off clips/ latches on top of drum. Remove small bolt that holds on the small plastic unit unto trans. That will give you access to the large bolt that holds the hub in place. This nut is on tight use a pipe wrench and adjustable wrench and TURN CLOCKWISE TO REMOVE - lock for direction on nut. Remove the bin gently and turn over to remove the small bolts that hold the hub in place. Installation is reverse of removal.
My husband was unavailable and already overloaded, so I took a screw driver and removed the front cover of the washer. After I discovered where the leak was coming from, I used a screw driver to remove one end of the hose and pliers to remove the other end. I went online, found the part and ordered it. It came in surprisingly fast. My husband put it back in about 5 minutes.
Transmission bearing went out creating alot of noise on every cycle.
I had to remove top control panel and flip it over the back and out of the way, but did not have to unplug anything. I then had to remove front and top panels in order to remove the agitator and eventually the tub assembly itself. Once the tub assembly was removed, I had to turn it upside down to remove the transmissing and brake assembly as well as the mounting bracket. The entire removal process took about an hour and a half. The reassembly took less than an hour. The most difficult part was removing the 1 11/16 nut that ties the agitator to the tramsmission through the tub. It took 3 of us to hold the tub in place so that one of us could use the 3/4 drive ratchet and extension to loosen the nut. We did the same thing during the reassembly. All together there ware quite a few parts removed and a fair amounte of different screws. In order to perform this job, you must have a decent tool set and the ability to diagnose each step of the process, but it's not very difficult otherwise.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
13 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
There was no hot water coming out, I had already checked the screens
First I removed the old part (2 screws) Pulled off 4 wires (maybe the wrong word, I'm not a professional! Put the new part in-turned the water on and had a stream of HOT water-yay I had been putting this off because no one in my family had noticed (except me) and with my husband out of work it seemed like a low priority, but when my daughters came home for Christmas, they said "There's no hot water in the washing machine" so I took the plunge--I cannot believe I waited that long! It literally took me seven minutes!
Tranny oil ran out onto Laundry room floor/making noise
Removed front cover(use screwdriver)clips on top of cover under lid Disconnected power from wall Disconnected wires to motor 1 screw/unplug for motor Uncwrewed clamp on drain hose Removed top lifts off easliy With help released Washing drum assy from hangers Slid back and Tilted drum assy outwards from drum opening out to the front of machine Pulled agatator up and off of hub Remove one bolt from hub 1/4 " rachet w 3/8" socket Pull off cap Removed Locking nut(couterclockwise)nut is soft metal used good vice grips firmly locked on nut Removed inner washing drum Turned over Entire Assy (motor up) Removed belt (slid off) Removed 4 blots from Motor/Tranny assy to Plastic outer drum Lifted off Motor/Tranny assy and pulled tranny out Reaasemble in reverse order witht the exception of replacing the hub seal(inside)Outer drum assy. There were service instruction under the front control panel.
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
13 of 15 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two paddles on the agitator broke off.
After reading how others have done this and how easy it was, I decided to give it a try. And, sure enough, it was really easy. However, one concern I had was on lifting the old agitator off from the axle using both hands. I didn't want to have the agitator come crashing into my face as I pulled up. So I put a pillow on top of the agitator.
Left up agitator, use socket set to remove agitator coupling. Then replace old agitator coupling with the new one. Tighten nut with socket set, replace agitator. Yes it is that easy.
Noticed 3 straps were broken when we replaced the hose
I removed the front cover, then unscrewed the top to expose the top. There are two screws that hold each strap, which turns out are different sizes, so I had to use two different sockets. I also had to remove the hose & plastic tube for the bleach. Once that was done, the replacement was easy, I replaced all 4 straps, reconnected the tube for the bleach, screwed the top back on and snapped the front cover into place. This took maybe 30 minutes - and I am female!
I remove three screws on top of the washer, moved the cover of the machine in order to get access to the water valve, and then desconnected the two solenoid of the valve,and removed two screws that hold the valve with the frame and installed the new valve in same order a took the old one.
Tipped washer over on to the front side. Removed back panel. Removed the flex coupling to the water pump. Removed the old belt. Installed the new belt and reversed the process to put components back together.
Intermittent overflow. You never knew when it was going to happen. Called GE Service, guy comes out and $110 dollars later he tells me there is nothing wrong with the wash machine. I must have overloaded it. Days later the machine overflowed 3 more times.
Got on line and hooked up with Parts Select and found thru similar stories that the overflow problem with this GE wash machine was a common problem and was explaned what parts were needed and described how to access the parts inside the control panel. So I ordered water valve 1155105 and pressure switch 269820. I pulled the plug and turned the water supply off and disconnected the hoses. Pulled the knobs off the front panel and removed 4 screws. I identified the parts and how they were attached. Removed the wires and removed and replaced the parts. Put everything back together and the machine works great!