Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
oven will not lite.
this is the easiest repair possible. take out bottom drawer.. disconnect power cord. igniter is above burner grid.remove the two screws {be careful not to lose them}. move stove out from wall. from behind stove remove three small screws holding tin cover. and unplug the connector..install new igniter from under stove and plug in connector. install tin cover and move stove back in. replace bottom drawer. and plug in power. replacement saved the repair cost or replacement of a new stove..
Even though the old igniter still glowed, I took Part Select's advise that it may be getting weak and ordered a new one. They shipped the part out the same day, very nice, however FedEx decided for some reason to hold it for five days before moving it along. Boo! When the part got here the fix was straight forward, just a matter of unscrewing a small back panel, unplugging the part, taking the old igniter off the burner and reversing the process with the new part. Oven lit right up. Thank youfor your advise and quick service.
I basically followed the video. The hardest part of the repair was trying to squeeze behind the oven to remove the back plate. Also the original screws holding the igniter took a small Allen wrench that I didn't have so I used an adjustable wrench. One screw was a little difficult but eventually got it tightened. Otherwise this was an easy repair like other reviewers have said.
Igniter was failing to get hot enough to ignite the gas.
It was a very simple repair pulled the old ignitor, and installed the new one in under 15 minutes. It was nice that it was a factory original part and matched perfectly. The wiring plug matched so no need to cut the plug and get ceramic wire nuts. The ignitor works perfectly and gets white hot rather than dark orange, the gas ignites in 20 seconds compared to 90 seconds.
Oven would not get to temp. Igniter glowed but no gas to burner.
Easy. Slide oven away from wall. Turn gas off and unplug. Open oven door. Remove grates and lift out bottom tray to access igniter. Igniter is affixed to burner tube using (QTY=2) 1/4” bolts. Used socket wrench due to limited space for nut driver handle length. Detach igniter. Got to back of oven and remove the protective plate at the bottom. There are three phillips screws. Verify you have the correct cable for igniter by tugging on igniter in oven. Pull old igniter out. Replace old igniter with new using old bolts! Run igniter cable through back using same hole as old igniter. Plug in connector in the same fashion as prior. Before reassembly, test oven. Plug oven in and turn gas back on. Set oven to bake and set temperature. If igniter lights the gas burner tube, you’re done! Reverse process to put oven back together. Job takes 20 minutes, maximum. Saved a bundle!
Pull range out from the wall. Unplugged the old igniter. Took the broiler assembly out of the bottom of the oven by removing 6 philips head screws. Removed the 2 screws holding the igniter & removed. Screwed the new igniter in place , replaced broiler assembly. Got back behind range plugged in the new igniter slid range back into position & turned the oven & it works like a new one.
Unplugged stove. Pulled stove out. Unscrewed screws and removed cover. Removed & replaced sensor. Reinstalled cover & screws. Plugged in stove and pushed back in. Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
Moved oven away from wall, Turned off gas and unplugged electrical from wall. The igniter has a coupler plug that you have to unplug from behind the unit. Take out the bottom drawer. Remove the 2 nuts holding the igniter in place. Remove old igniter. Replace with the new igniter, screw in nuts and thread connector wire to back of unit. Reconnect the igniter behind the unit. Turn on gas and plug in electricity. I checked to make sure it worked before pushing it back into place. I also took time to clean up while the oven was pulled out so it took about an hour - 15 minutes to replace the part - 45 to clean up. Works and looks just like a new oven range!
I shut off the gas and removed the back plate and disconnected the wires. Then I unscrewed two screws from the igniter and replaced the old with the new. Then I snapped the wires together and put the back plate back on. The oven works great!
changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.
I pulled the stove out from the wall & took the back lower right cover off. Unplugged the power cord & disconnected the igniter from the power. Took shelves & bottom cover (took two screws out)from oven. Used nutdriver to remove old igniter, then pulled the connector through into the oven, discard. Put new igniter in place with nutdriver.Push connecting cord through to back of stove.Replace bottom cover & shelves. Plug cords together & plug cord back in to outlet.Turn stove on & igniter works!!! Push stove back into place & bake a cake! :)
most difficult part was having to pull the stove out to access the Igniter wire connector. unplugged connector, removed 2 Igniter mounting screws, installed new Igniter and connected plug. very easy project. less than 30 minutes total thanks to website for perfect diagnosis of problem
Removed bottom plate by pulling up from the back (had some resitance), Two machine screws holding cover over igniter, used 3/8" socket to remove. Pulled oven from wall to disconnect igniter @ coupler, unscrew one more machine screw, fed replacement igniter into slot and coupled, attached single screw to pipe, put cover w/ 2 machine screws on top, install bottom plate. Had to use butter knife to get bottom plate to fit into the front cabinet area of stove. Done & working fine.
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.