Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Code indicating washer was NOT discharging water
Watched the video, procedure was simple and as depicted on the video. Started by using a wet shop Vac to the discharge hose and sucked as much dirty wash water out as possible. Removed the pump,and found the motor did not turn freely. Removed the motor (3 screws) and replaced the motor with new part. Reassembled the washer, everything worked as it should. After about 3-4 loads of laundry, the "Not Draining" code / problem returned. Again, sucked out the water with the Shop Vac. Checked the Filter /Cleanout and found it completely packed with MUD. Cleaned that out, and again disassembled the washer. The pump was removed and the remaining muddy gunk was cleaned from the impeller. The 3 drain lines that attached to the pump were inspected for blockage/obstruction and flushed of any muddy residue. Reassembly was quick and easy, and the washer has worked well since. I have no idea how the dirt got into the system with enough dirt to gunk up the system. Recommend keeping more frequent inspections of the cleanout trap.
First I removed the retainer ring and then pulled back enough of the boot to get the door switch out and plugged in the new switch put the retainer ring back on and it was finished. With out the repair book I would have been lost on how to do the job.
Took off bottom panel by removing 3 torx screws. Opened up door seal, removed three latch retaining screws, unplugged three wiring harnesses. Installed new latch and reinstalled in reverse order.
Removed 2 screws from rear of top that hold top of washer in place, lifted top at the rear and slid it back then lifted it off. Removed the three wiring harnesses from old switch, removed the three screws holding switch in place, theses are accessed from the door opening. removed the two lower screws first and held the switch from the top while removing the last screw. Placed new switch in place and started the top screw by hand followed by hand starting the remaining two screws, tightened screws with phillips screw driver, reconnected the three harnesses, reinstalled the top and secured with the two screws. Door locks and unlocks as it is supposed to.
door would not latch , and lights on front just flashed
1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.
Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.
First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wire tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.
I removed the spring that goes around the rubber on front of drum, pulled back rubber near the lever, removed the 3 screws holding in the latch, reached in and disconnected the 3 plugs to part, connected new part put it in place screwed it in, put the part of rubber i pulled back, put spring back around the rubber, plugged machine in done
Removed the rear top two Phillips screws, pull off top cover. Unscrew two phillips screws that hold the outside front lock trim, unclip (one left of housing) plastic housing. Remove one phillips screw 11 o'clock from housing, about 6" away, with door button above it, which releases the door lock housing from inside the machine. From right side (facing machine) look down into left front of machine, you will see a black cover, which does a goid job hiding the white part, but it protects the part from water, I guess. Unclip 3-4 plugs, push spinning loader away to pull out the complete part easily. Swap back covers (a bit annoying to place wiring harness back in such a tight place, and cover on. You can try another method if you have a simpler way, like place the harness onto part first, before plugging in and placing cover. But, I kept dropping the part into the machine, which equals a little pita). Then screw the 11pm screw to hold part and the two other screws (small housing and cover), place remaining 2 screws, and lid. Pretty much undo the above procedure. Done.
Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.
Replaced door lever (PS11741552) and door lock latch (PS11745016).
Initially I tried to replaced just the obviously broken (split) door lever, but then door would not close at all. Lever is as simple as it gets, so the problem was apparently the door lock latch.
After watching video (on this site) that shows it was fairly easy to access and install a new door lock latch (2 screws in back, 8 screws in front), I ordered a new door lock latch.
Took about 35 minutes to install new lever and latch.
Works perfectly now. I hope to get a few more years out of this machine.
easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.
Both door latch parts broke, one on the door and the other on the washer.
When I looked at the website for latch repair they showed a video (can't remember which brand but not Amana) where you had to take off the top and front of the washer to get at the latch part on the washer. For the Amana I had, you simply had to pull out a portion of the rubber gasket held onto the washer by a wire/spring combination (you can take the wire off) to get at the latch assembly. You could then undo the three screws holding the latch to the washer, pull it out and unplug the three wiring connections to remove the old latch. Then plug connections into the new latch, reinstall, tighten screws and fit gasket and wire/spring assembly back together. Much easier than going thru the top and front of the washer!
