Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Broke one of the lugs that attach to the range door that door handle attaches to.
Removed 2 screws on inside of oven door being careful not to let front oven door glass to fall off of door. It would probably be a good idea to use tape to hold glass on door before removing screws. Lifted out trim piece with handle and then removed handle and attached to new trim piece and screwed it back onto oven door.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Opened the breaker for the oven. Verified the power was off. Removed the racks from the oven. Using a screw driver removed two screws in the back of the oven holding down the steam bake bottom of the oven, pulled up from the back to get the pan out. Removed the screw holding the front of the element in place. Removed the screw in the shiny metal of the element at the back. Gingerly pulled the element to the front and as the element stopped slightly turned the element to let the prints come out. That part was challenging to get the angle right so not to damage the wires. Using a small Phillips screw driver I pushed in on the connector latch on the terminal and then pulled the terminals off the element one at a time. Follow all the steps in reverse to install the new one.
Stove top wouldn't come on. Oven couldn't go higher than low heat
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00 Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine. Thank you, Thank you Part Select for your help and honesty.
Unplug the appliance, remove the bottom cover inside the range and the cover in the rear to unplug the heating element. R&r the element, reinstall the covers and test for proper operation.
Lower Element had gone bad. Not able to keep temp up.
1) unplugged rnage from wall 2) took off back plate to unhook electrical from element 3)took door off of range for ease of access 4) removed the 2 screws i the back of tha bottom panel 5) removed 1 screw in front and 1 screw in back to be able to remove old element. 6)remove element and replace with new one. 7) reinstalled both screws and the bottom panle. 8) connected electrical to new element 9) replaced back cover and plugged in unit to wall 10) put range back in place.
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
I pulled the range out from the wall, then unplugged it from the wall outlet. I removed the oven door & set it aside. Removed the screws covering the rear wiring shield, then disconnected the 2 leads from the bake element. Unscrewed the screws holding the oven floor pan, then unscrewed the screws holding in the original element. Replaced it, screwed everything back together, and pushed the oven back against the wall. Took me about 30 minutes, and now the oven works as well as it did when we first bought it.
Unplug from power source, remove panel on back of range, unplug power connections for bottom element on back of range, remove bottom pan in oven installed element, put back together in reverse. Video on parts select website is the bomb!