Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replacing broken glass dryer drawer from a sharp golf ball size rock from kids.
Glass door was broken with part still in door. -put tape on glass so it would not fall on me as I dissembled door. -removed and disassembled door by removing all screws/ torx. -used shop vac to get most of the shards out then flushed with water for the rest. -used shop vac to dry door. -put back together. remember to put big bulge of glass down. the rounded part of the door is the bottom. do not over tighten as the screws go into plastic. -all skill levels can do this job. it will only go together one way. the glass has a notch bulge that alines with the bracket. worst case is you have to put it together 3 times before you get it right. the door is reversible so it can open either to the right or the left giving you four combinations on how to install the glass. don't over tighten the phillips as they go into plastic. Go for it.
Coin op Whirpool Dryer Broken drive belt and frozen drum wheels
Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)
rollers on the tub had worn and the tub was no longer balanced.
sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.
I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.
My dryer would not heat. Drum was spinning fine and everything else was working just no heat.
I removed the base cover and cover over my lint blower. The thermal fuse is located on top of the blower housing. I removed the thermal fuse utilizing a small nutdriver and installed the new fuse.
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
Take pictures along the way. 1. Remove lower front panel using screwdriver to lift up on tabs on top of panel. 2. remove door 3. unplug moisture sensor plugs 4. remove lint trap 5. on back of dryer, remove screws holding upper lid 6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on 7. remove the front panel screws mentioned in step 6. 8. Remove lower front panel screws 9. remove front panel 10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys) 11. slide out tumbling drum 12. with drum removed, use socket wrench and socket to remove old idler pulley. 13. install new idler pulley 14. reinstall tumbling drum 15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley. 16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly. 17. Reinstall front panel 18 slide top panel back into place and secure with screws from back 19. reinstall door 20. reattach moisture sensor plugs 21. reinstall lower panel
Dryer motor bearings failed. Motor wouldn't start.
Disassembled dryer. That was the hard part. Figuring out how to get the top off the dryer so I could get the drum out took the most time. The end caps on the control panel had to be removed by forcing them outward to release the plastic catches. Then the bottom corner screws were removed to allow the panel to swing up out of the way. The top panel could now be removed. To gain access to the belt and tensioner the blower and ducting off the front of the motor had to be removed to remove the belt. Now the drum was able to be lifted out. The motor swap was a cinch with no wiring modifications required. Reassembly was the reverse, with the most difficult thing being tightening up the blower fan. This required putting a wrench on the belt end of motor shaft and holding it while reaching thru a narrow gap on top of the fan ducting.