Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door just fell down
Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit
After I finally got the right parts and installed them I discovered that even though I had bought the OEM part for my dishwasher it not only didn't fit but prevented me from even getting the upper rack back in the dishwasher. The dishwasher won't work with out the upper rack properly in place. Every part store I looked at offered the same part for my dishwasher so obviously Whirlpool made a huge mistake. Since it's not possible to get the old parts back on (one of them was broken anyway which is what started all of this) I had to buy a new dishwasher. I did contact Whirlpool by email but got no response. If you own a Whirlpool dishwasher be very cautious buying any replacement parts.
A plastic retainer pin for the bottom kick panel was missing.
simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver. NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.
Replacement parts from factory installed using u tube support video
Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place
Kids loved to make squeaky sounds opening and closing the doors, finally snapped the door balance link on one side.
1) clear out the dishwasher 2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top 3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection 4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online 5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides 6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point 7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them 8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame 9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly 10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame 11) you've done it! 12) have a cuppa and do your second washer that hasn't failed yet - it will soon.
Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.
Order both this seal and the seal for the bottom of the door at the same time.
All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,
With a little pressure, I was able to push off the broken wheel pieces with my thumbs. I was able to snap on the new wheel pieces really easily. This job took less than 15 minutes to replace all 4 wheel pieces.
Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.