Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.
Door seal badly damage do to heavy lime in the water
Remove the old door seal by pulling it out. Take the new seal find the center of the new seal by lining up the ends so they are even. Push the new seal starting with the center you just found at the top center of the machine. Push it in to the slot as far as it will go going both to the right and they to the left so it stays even. At the bottom of each end cut the extra on a angle. Use a screwdriver to pry to old strike out and push in the new one. Your done.
Followed the video. It works perfectly. Used a small paint scraper to remove stubborn scale where gasket seats. Used steel wool on door to assist in removal of rough scale.
Dishwasher not draining on final cycle and smelled of burning
I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.
I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.
Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.
front track stop broke on both sides of the upper tray
Very simple to repair The front track stops just slide into place, easy. When I looked for these parts this place was the least expensive and the quickest delivery I have ever had. Quick, efficient and friendly online staffing. Thank you, Deb
Water trickling out of sprayer on top rack not strong enough to clean dishes. The back of the water manifold was broken off.
Removed top rack from dishwasher by removing retaining clips on roller track and slide top rack out of tracks. Placed top rack on table upside down and popped water manifold out and snapped new one in place. Install rack in reverse order of removal. Note: Make sure there is no food debris clogging spray arm, that will give same symptom as well as a weak or clogged pump.
I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.
Dishwasher Not Heating top rack wet dishes and heating rod looks rusted
It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.
After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.