Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 4 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher door drops quickly to wide open position when unlatched
Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Dishwasher not draining on final cycle and smelled of burning
I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.
Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.
Had to repurchase the correct one. I was also sent a used part that I am still waiting for a call tag to send back. I was also given an email address for customer service but low and behold it also didn’t work!!!!
I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.
based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.
Heating element went out, dishwasher wouldn't work
I checked the manual to determine the code meaning for 7 blinks, it was heating issue. I ordered the part from Partselect.com. When the part came in, I googled the internet for "How to replace a dishwasher heating element". There were several options, I chose one that was a video showing a handyman go through each step. I followed the steps, with no problems, and WA-LA! Felt good (as the wife of the house) to do it myself!
