Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water leaking from between inner shaft and outer shaft of assembly and teeth worn off of clutch assembly
Followed instructions from video for shaft and mode shifter assembly and tub bearing, all went as in video except extremely difficult to remove tub nut. Could not get nut to loosen and when it did finally move it was spinning the whole shaft, had to have the shaft held with a pipe wrench from underneath (2nd person). The tub seal was another issue, removal was easy just as in the video but because water had gotten inside the seal it caused the internal metal of the seal to corrode and rust which deformed the old seal and the plastic of the tub where the seal sits. There was no way the new seal would go in and be tight enough to seal so I put a hose clamp around it, heated the plastic with a heat gun just enough to be able to tighten the clamp several times, let it cool and removed the clamp. It held its shape and the new seal went in snug so I proceeded with the reassembly. Test ran the washer and checked for leaks, no leaks. It has been a week now and approximately 10 loads of clothes cleaned, all is good.
Followed your video instructions and removed agitator.Used 7/16 3/8 in socket wrench to remove bolt in the agitator coupling and replaced coupling. Put new bolt in and tightened. Installed Agitator.Works Great.
First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help. sincerely, a satisfied customer
The machine would not spin and the agitator seemed to be siezed up. The inner tub had cracked and broken completely loose causing it to jam against itself preventing any movement.
1.Pulled the agitator out. Unscrewed the top nut, which was a little tricky to break loose since it had been in place for over 10 years. Pulled out the entire washing cylinder to unscrew and replace the hub. Not bad but you need to take out the inner tub and that requires doing a little extra unscrewing and prying.
We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.
First I located the trouble. I noticed that it was water leaking and figured it had to be a hose. I took the front panel off of the washer and after noticing that the drain hose had a slight hole in it, realized that I could fix it and save myself a repair call. I undid the two hose clamps and removed the hose. I went to a local repair shop that could not guarantee the right part. I went online and found Parts Select.com. I entered minimal information and the picture of the item that I was looking for, the Drain Inlet Hose, was staring at me! Within 3 business days and less than 20 dollars spent, I repaired my washing machine. The total time spent to repair after I received the hose took about 10 minutes. I will definitely use parts select .com and recommend to all my friends and family. Thank you.
I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.
I pulled on the bottom edges of the agitator, like the video said, until my fingers were numb. Finally, after I got aggravated, I beat the old agitator into a hundred pieces with a hammer and chisel. Then I slid the new agitator into place and gently tapped on the top of it. It snapped into place and has worked like a new one every since.
The repair would have gone well, however partselect sent me the wrong part. Instead of a washer belt, they sent me a door seal to what looks like a refrigerator
Followed video on You tube that showed step by step how to compete repair. The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine. Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.
Reached down into the washer bowl. Fingers on each side of the agitator base. Quick jolt up agitator popped out adjustable wrench took the bolt. Off of the agitator coupling removed coupling wire, brushed the gear slots installed a new coupling with both new bolt lined up, agitator slots pump, the new agitator on after lined up with a down force quick jolt, then installed the new fabric softener, part on top of agitator
The pump was easy to put on the the washer still doesn't work . The water still just drains out.
First I took the bottom of the washer off so that I could get to the pump then I took a socket set to take the pump off. Then I put the new pump on and put the bottom of the washer back together.
Wife noticed water pooling around the washing machine
Unplug the washing machine. There are electrical components that can injure or kill you. Using a screw driver inserted just below the lid of the washer in the front, there are two (2) spring clips that you push on to release. Then the front of the washer tilts down and you remove it and set aside. On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.