Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The pump was easy to put on the the washer still doesn't work . The water still just drains out.
First I took the bottom of the washer off so that I could get to the pump then I took a socket set to take the pump off. Then I put the new pump on and put the bottom of the washer back together.
Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!
Removed three nut screws and raised the control panel forward twisted the old switch off removed one wire at a time and put it on the new switch. I did this so the wires would be where they should. After I put the new switch on I replaced the three nut screws I plugged the washer in set it on cold water and it worked like it should.
I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.
Ordered new pump on Sunday - replaced on Wednesday. Removed front washer panel with putty knife to release latches. Used pliers to disconnect hose clamps. Lots of paper towels to sop up water in bottom of washer and on floor. Unhooked electrical wires. Socket to remove pump. Reverse actions to replace pump. It's "plug and play"!
1) Researched internet for parts to make repair 2) Tested the cold side to make sure the only problem was the valve. 3) Ordered part from PartSelect 4) Made repairs after going to hardware store to purchase a set of torx bits to loosen the front panel so I can replace the dual valve assembly.
The picture of how to depress the clips to remove the front was incorrect. The clips are 4" from the sides not immediately at the sides per the picture. The 4 rubber springs were only part of what was needed for the washer. The old gas dryer was still working. There are two more springs on the bottom of the tub missing not shown on diagrams, so it still sways side to side, bangs around and makes a lot of noise. After putting on the 4 rubber springs, it ran, but probably needed a new clutch also, because it wouldn't spin dry anymore. I ended up spending $2000 for new washer and dryer from Maytag, and throwing out these old machines today.
Replaced the knob. Identified the appropriate knob which was easy because of the drawings on your site (PS271124 Timer Knob with Clip). Ordered knob, arrived the next day. Slipped the knob on the washing maching controller. Perfect.....took 2-seconds.
Would agitate, but not spin, leaving clothing soaking wet.
The hardest part is lifting the washer to get a the bottom. Disconnect the power, shut off water. Disconnect hoses and drain hose. Move washer from the wall about 2 feet. Tilt up front of washer. I used 4 12" long 8x8 inch lumber, lift washer….place one on each from corner. Lift again, place 1 more 4x4 on each existing 4x4. Now remove the belt off the 3 pulleys. Use the flat blade screw driver to remove the C clip holding the Pully on the shaft, with the flat bladed screw driver and hammer. Once the C clip is off remove the metal washer, pulley, plastic lock (apart of the bottom of the pulley & the thrush bearing and it's washer. Using the parts supplied (the "new thrush bearing is a bearing and washer combined) replace as you removed it. Thrust bearing, pulley, washer and, c clip. I tapped mine on using the flat bladed screw drive……becareful not to break it (they did supply 2 for me in the repair packet) make sure he c clip is secured. Lower the washer after removing all the tools from under the washer, by reversing the lift sequence. Slide the washer in place. Connect the hoses back up. Plug it in.Reconnect the drain hose, you should be good to go.
The agitator "wings" are open at the bottom so any clothes with strings gets caught in these wings and eventually brake the wings off.
I watched the video provided by your site and followed it. I removed the clothes softener part from the agitator, Got a good grip on the agitator and pulled up. It came right off. Aligned the new agitator groves and slid it into place, put the fabric softener part back on! Super easy.