All Installation Instructions for Magic Chef Washer W209KV

The washer was jumping all over the place and leaking water during the spin cycle

I took out the agitator first, then I took out the inner tub, next I took out the outer tub, and last I took out the transmission assembly. After replacing the snubber I put the transmission assembly back on, then the new outer tub and next the inner tub. Last I put the agitator back on.

Parts Used:

Plastic Outer Tub

Screw

Snubber Ring

Elmer from Fort Campbell, KY
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

4 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

part received one day after ordering, excellant

took back off washer with nutdriver, pulled wires off by hand, ( was unplugged ). pliars used to remove hose, regular clamp put back on. reinstalled back plugged in, tested water,,,, done

Parts Used:

Water Inlet Valve

jrrry from Sebree, KY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

water pump locked up and burnt motor pully and belt

repaced faulty pump,motor pully then installed a new belt

Parts Used:

Drive Belt - 51 inches long

Plastic Motor Pulley

Gerard from Durham, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

water leaking under washer

removed rear acess panel and used pliers to remove leaking hose then reinstalled new hose..

Parts Used:

Tub to Pump Hose

paul from akron, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water leaking when washer was filling with water.

Took off the back plate. Looked to see where it was leaking. Squeezed the clamps on top and bottom to remove from hose and pull hose out.

Parts Used:

Tub to Pump Hose

Colleen from Glenflora, WI
Difficulty Level:
Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Pully. Seperation

I just put the pully on then put the belt on and started washing clothes thank you very much for your help in getting me the pully in a timely matter aloha

Parts Used:

Plastic Motor Pulley

Charles D from New Castle, WA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken lid hinge pins

I raised the top of the washing machine per video instructions, removed the screws, replaced broken hinges with the new ones. It was simple as that.

Parts Used:

Lid Hinge Pin

William from LEXINGTON, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Hinge Broken

Removed screw, replaced hinge.

Parts Used:

Lid Hinge

Angela from FACTORYVILLE, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Tub to pump hose worn out and leaking

Replaced the hose. two clamps and retainers. very basic repair

Parts Used:

Tub to Pump Hose

steve from WATSON, MN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Noise

I changed the piece easily

Parts Used:

Snubber Ring

Marylou from Old Forge, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken Hinge Pins

I used the putty knife to release the spring clips on the machine lid. They are about 3" in from the side of the machine. Then I lifted the top of the washer up holding the lid in place. I then used a screw driver (torx) to remove the hinge from the bottom of the washer top. The lid should come right off. Then I the removed the broken hinge pins from the back of the lid with a screwdriver and replaced with the new parts. There is a little tab that the pin fits in the lid to assure you have the pin installed correctly. Then I slid the hinge back on the pin and reversed the process reinstalling the hinges and closing the top of the machine over the spring clips and your done. Very easy repair that I completed in less than 15 minutes.

Parts Used:

Lid Hinge Pin