Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven Wouldn't Light. Smell Of Gas Before Lighting
First I went online to find out about the availability of the part. In my search, I found what others had experienced and how they repaired it. Second, I ordered the part and followed others stories on their repair efforts. Third, I unplugged the range and removed the racks. Fourth, I removed the bottom of the oven which lifts out back first. Fifth, I removed the wing nut securing the flame difusser making it easier to access the element. Sixth, I had read that others had problems saving the original screws and/or threaded holes. I sprayed some wd-40 on both screws. They came out and back in without a hitch. Seventh, I removed and replaced the element, snap out, snap in. Eighth, I turned on the oven. It took about 15 seconds to glow but wow, it lit 5 seconds after that. I am my wife's hero!
I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back. I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
my sreen wasn't working , but when i touched the buttons i could hear the sounds.so i decided that the screen just burnt out.so i took it apart 4 phillip head screw.that easy then i un pluged the wires 4 of them all different shapes and sizes no brainer.4 more screws to remove the screen.Insalled new screen.matched up the wires with there pin count.and whala done replace it back on to the oven.replace the the 4 screws and done.works like a charm.Oh don"t forget to kill the power unplug it and if it's hard wired shut it off at the panel.should be marked stove oven ect.most important kill the power or they"ll be trying to fix you good luck
Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..
I removed the flame baffle , removed the two screws that held the ignitor. Then I pulled the wires thru the back wall and disconnected . I had to cut the the connector and install with wire nuts because connector was different. Works fine now .
oven took too long to light, then lit with a whump sound
I read all the reports on your site pertaining to oven igniters and decided to order one. I was amazed when it arrived the next day. I got a lot of tips reading others replys so I lifted off the oven door, took out the racks, removed the 2 screws holding the old igniter and tried to pull it out. There was hardly any slack in the wires, so I pulled the stove away from the wall, took off a breadpan size cover in back and found the wires were zip tied to a tube. I cut the tie and unplugged the wires, but the new plug didn't match so I cut the new plug off and rejoined the wires with butt to butt crimp connecters, which I prefer to wire nuts. I used the insulation and new cover from your kit as my old part had the long ceramic insulator and put it all back together. It works like new again and saved me a lot of money. I am very pleased with your product and service, thanks.
The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I would absolutely use your services again. Oven is back to working great! Thank you!
Removed burnt bulb. On replacing the bulb I glued the bracket, retainer gasket and bulb cover together- I used only a small amount of glue-just enough to hold the three items together. You need to do this since the three items slip in your hand while you attempt to screw the bracket to the oven wall. Need my help, email me @ Lexidog999@tx.rr.com
Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Strong odor of gas when oven in use. Oven took over a minute to light with low flame level (ie 1/4").
Removed bottom plate from oven enclosure. Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven. Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ignition was less than 15 seconds with over one inch flame from burner.