Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Door handle was damaged during move from another house to my house.
removed 3 phillips jead screws. removed old hangle. cleaned around the site of old grime./ smile. positioned new handle, applied the 3 screws, tightened, and " whalah" like new.
First I removed the old handle by removing the 3 screws holding it in place. There are 2 on the top and 1 at the side of the door. When I began to put the new handle on it became apparent that the metal frame inside the handle was not aligned perfectly with the old screw holes. The plastic is not even with the door horizontally on the top, but it fits otherwise. Be careful not to over tighten the screws when installing. Pretty easy overall.
Removed a small cover plug on the lower portion of the handle, removed three screws. Took off old handle, positioned the new one, replaced the screws and cover plug and that was it! Wouldn't have taken even 15 minutes if I hadn't dropped a screw and had to search for it - lol.
First I removed all the screws from the back cover. 2nd removed fan nut and fan blade 3rd removed fan bracket 4th I traced wire to the condenser and disconnected wires from wire nuts. Installed existing fan brackets to new motor kit then reconnected wire nuts to new motor cord Reinstalled fan nut and blade, reinstalled cover, plugged it in and BAM .WORKS PERF!
The problem was a cracked adjustable shelf on the refrigerator door. I knew that I could easily get a new one from Part Select, as I had replaced internal shelving parts before.
My repair job was probably the easiest one of all, as the new shelf was simply snapped into place and the job was done. I saved a lot of money from buying the part locally too.
Outer case of freezer was heating up, not making ice (sometimes) turned up thermostat several times (especially freezer)
I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.
Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well
Exposed evaporator and fan.Turned refer back on. Evaporator started to get cold but fan did not run. Removed fan and applied 115 volts. Fan did not run. Installed new fan kit. Old refer works as good as new. Vary easy job. I almost bought a new refer. Glad I didn't. Probably saved myself $500+ Shopped several sites on internet. Other sites wanted about the same price for motor only and 15-20 bucks more for the fan. Vary pleased that I found this company to buy this part. Received fan kit in just a few days.
Removed old handle with a total of three screws, two on top and one on bottom of handle. Replaced with new handle and put existing screws back in place. Very easy!
Removed 2 screws from top and removed bottom cap cover to access the bottom two screws for its removal. Replaced handle by using the same screws and put back the small plastic cap cover and DONE.
Replacement was extraordinarily easy. It took about 5 minutes, including the time to find my tools and put them away after I was done. As others have warned, only the handle itself was shipped. The trickiest part was being careful not to break the little plastic cover at the bottom of the handle when I pried it off. Apparently a screwdriver under any edge would have worked okay. There were three Phillips-head screws (replacements were not included in the package!) - and that was it.
Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket
I ordered the post, pulled it out of the box, pulled off the glass, pulled out the drawers. I looked at where the post looked like it shoul go and put it in. put the drawers in, glass on. It took me about 5 minutes and everything is perfect.
