Models > SUD6000HQ0 > Instructions

SUD6000HQ0 Whirlpool Dishwasher - Instructions

All Instructions for the SUD6000HQ0
121 - 135 of 268
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
leaking front door. loose seal.
Followed instructions, those were OK.
Dishwasher front still leaking
Parts Used:
Heat Resistant Adhesive
  • Frank from SANTA ROSA, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top glass rack broke
Just watched the YouTube video they recommended watching and it is very helpful. No tools needed and was finished in several minutes.
Parts Used:
Rack Adjuster
  • James from MILFORD, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Insulation needed replacing
I searched for the 18x5x5 insulation.,ordered it from Part Select. Waited. Company sent wrong part. Called, they gave me a refund, reordered, promised 2 day free shipping. Waited more than a week, paid for 2 day shipping. Received same, wrong part. Still don't have repair done. Looking elsewhere for part.
Parts Used:
Access Panel Insulation with Glue
  • Mollie from CANTON, NC
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Soap door wouldn't open.
I looked online to see a video. Dad to pop lid off soap dispenser. Slide a plastic part to the left n the spring slide off. Video showed how to place prongs on spring . Then had to lift the upper part of spring to lift onto plastic part of soap dispenser. That was it.

Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.
Parts Used:
Spring, Lid
  • Anthony from CLEVELAND, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
P piece of the adjuster rack was deteriorated and broke off
Crazy Glued it together until we received the new part, but it fell off again. My husband installed the new piece and said it only took him about 2 minutes. You just take off the end cap and pop in the new piece and adjust to match the one on the other side of the rack. He said it was extremely easy and no tools required.
Parts Used:
Rack Adjuster
  • Kathleen from PALATINE, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
THE LOWER RACK WAS CORRODING IN SPOTS AND WAS RUSTING
THERE WERE NO INSTRUCTIONS INCLUDED, COULDN'T FIGURE 0UT HOW TO INSTALL THE NEW ROLLERS ON THE NEW RACK FINALLY INSTALLED THE OLD ROLLERS ON THE NEW RACK AND THEY WERE MUCH EASIER TO INSTALL I DONT UNDERSTAND
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
Parts Used:
Lower Dishrack Kit
  • JOHN from JUPITER, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken trolley axle in rack adjuster
No tools required except possibly a small screwdriver to help remove stop in end of rack; part easily installed by hand and stop re-inserted. Finished in several minutes. Thanks!
Parts Used:
Rack Adjuster
  • Jerome from Wiggins, MS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost the cap to the Rinse aid container in door
Ordered part, recieved part package, opened package, inserted screw cap rinse aid tank cover, twisted to close. Job completed. Time required about 15 seconds from opening package. Service was excellent and accurate. Thank you.
Parts Used:
Rinse Aid Cap
  • Bruce W from WESTERLY, RI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One door spring broken, replaced both
As described with instructions, removed original "bearing," installed replacement, removed original spring, installed replacement springs. Not difficult.
Parts Used:
Heavy Duty Spring Kit
  • Donal from SPRINGVILLE, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Parts Used:
Screw - 8-18 x 1/2
  • Johnny from LEVITTOWN, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dish washer leaking out bottom of door
New gasket did not fix problem. Cleaned air vent cover for steam to exit. Gasket not the problem but new one looks good. thank you
Parts Used:
Dishwasher Door Gasket - Gray
  • Ed from Ulysses, KS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher Not Heating top rack wet dishes and heating rod looks rusted
It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.
Parts Used:
Rubber Washer
  • Jose from HOUSTON, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turned out to be the timer!
So my dishwasher is 20 some years old. Woke up in the morning to smell burning plastic and the dishwasher never moving to the next part in the cycle. I thought it was the high limit, then the cycling thermostat(because cycling you'd think it was cycling wrong). Nope. It was working fine. I used a multimeter to test the high limit(ohm reading will be closed at room temp) and for the cycling(will be open at room temp, so use a multimeter with alligator clips and a lighter to trigger it to close). All of my existing parts were fine. So I went to the timer and tested with alligator clips, each part that connected during the timing cycle. Sure enough. On the rinse and pump water out part, the contact point wasnt connecting due to corrosion and a bent prong. So I rebent it and cleaned all the contact points. All you need to do on these old washers is pull out the timer and pull off the thin plastic "sheild" over the thing. Guess what. I have a working dishwasher after having done the impossible and fixed my timer. So for those who have a dish washer that won't advance, but you can hear your timer advancing with the clicks, this is your problem. Saved myself an unknown amount of money because they don't make my timer anymore.
Parts Used:
Cycling Thermostat Kit
  • Troy from MILWAUKEE, WI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Cutter Spring was totally disfigured and pulled apart. Not functional.
Repair went exactly like the video i watched online. Perfect
Parts Used:
Drain and Wash Impeller Kit
  • Aubrey from BERKELEY LAKE, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
DOOR leaking
door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking
Parts Used:
Dishwasher Door Gasket - Gray
  • mike from SHELTON, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the SUD6000HQ0
121 - 135 of 268