Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The part doesn't seem to fit the glass door
I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!
i watch video "silence a screaming whirlpool dryer (cabrio WED8000DW4)" by Brett Pagel I replaced the belt tensioner wheel, all glide wheels for drum and drum belt.
1st gen whirlpool Duet dryer sensor not working in automatic cycle. After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.
Door handle of stove's oven broke. Had problem finding handle until I contacted Select Parts.
The repair went well. Only took a few minutes. Oven is 21 years old and still working. I figured why throw away if still working. Thank you Select Parts for coming to my rescue. Will keep you in mind.
Loosen 2 screws and put new part in and tighten 2 screws. After putting in new sensor stove gave me another code had new part in 5 min and part select would not take my part back.
Oven was overheating and locking the door. Codes indicated the temperature sensor could be the issue.
Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board. Part Select was great to work with and accepted a return and promptly refunded me for the part. Thank you!
The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes
The side trim on the glass door needed to be replaced.
After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.
The Bake and Broil both stopped working. You could hear the igniters but no gas flowed.
Replace the gas valve. It is simple to replace, but please note that it comes configured for Natural Gas. If you are using Propane, there are two changes you need to make first.
1. Remove and invert the gas pressure regulator. See page 11 of the owners manual.
2. Tighten down the orifice hood all the way about 2 1/2 turns. It comes configured to stick farther up into the air mixer. See page 12.