Models > SBE22AA > Instructions

SBE22AA Amana Range - Instructions

All Instructions for the SBE22AA
31 - 45 of 131
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burner would not heat.
I unpluged the old burner and pluged the new one in. Repair done in about 2 min,
Parts Used:
Economy Y-frame Surface Unit - 8"
  • Jackie from Hughes Springs, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
No problem Took off old ones and replaced with new.
Parts Used:
Chrome Drip Bowl - 8 inch
  • Nicki from ELSIE, NE
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were not original to range, I could not get them clean.
I reoved old drip pans and installed new ones. Very easy, they look great!
Parts Used:
Drip Bowl - 6 Inch Chrome Drip Bowl - 8 inch
  • Lynn from BRADENTON, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
N/A
I followed the instructions provided.
Parts Used:
Surface Burner Plug-In Block Kit
  • Gerry from Mackay, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ELECTRIC BURNER SUPPORT FELL OFF AND BURNER SOMETIMES WOULD NOT COME ON.
Stuck the new one into the plugin.
Parts Used:
Economy Y-frame Surface Unit - 8"
  • RICHARD from SHOW LOW, AZ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip Pans were stained and burned on.
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Parts Used:
Chrome Drip Bowl - 8 inch
  • Sandra Collignon from SANTA CLAUS, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Used part
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
Parts Used:
Drip Bowl - 6 Inch Chrome Drip Bowl - 8 inch
  • Sabrina from FREMONT, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Parts Used:
Main Power Terminal Block
  • Elizabeth from HOUSTON, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Parts Used:
Main Power Terminal Block
  • Frank from Palm Coast, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans needed to be replaced
1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements
Parts Used:
Drip Bowl - 6 Inch Chrome Drip Bowl - 8 inch
  • Mark from ROSENBERG, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stove Burner wouldn't heat up
Someone did the repair for me.
Parts Used:
Surface Burner Plug-In Block Kit
  • Donna from Sandwich, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Sockets burnt out.
Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.
Parts Used:
Surface Burner Plug-In Block Kit
  • James from Bear, DE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Just needed new drip pans for burners
Was glad to get the correct ones for a 30 year old stove. Had already wasted $12 shipping trying to order from someone else.
Parts Used:
Drip Bowl - 6 Inch Chrome Drip Bowl - 8 inch
  • Ann from Cadiz, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip bowls very dirty and stained
Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering processes were simple and delivery was faster than I hed expected.
Thank you
Parts Used:
Chrome Drip Bowl - 8 inch Drip Bowl - 6 Inch
  • john from donna, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old burner pan warped.burner sat at 15 degree angle.
Removed burner and then burner pan.Then replaced pan and reinstalled burner.
Parts Used:
Chrome Drip Bowl - 8 inch
  • Michael from Portland, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the SBE22AA
31 - 45 of 131
Back to Top