Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Pump Leaking
I seemed to have a more difficult time changing the pump out than others who had left their instructions on line prior to me. What I has to do is remove the 4 bolts that secured the motor & mount to the frame. I then unplugged the wire harness from the motor leads. I removed the belt tensioning spring & removed the belt. I then removed the motor, motor mount and pump assembly. Turned it upside down & removed the pump. When installing the new pump you will need to remember how the belt was routed. A local parts house actually gave me a xeroxed schematic that showed me how to route it. A real life saver. After that I turned the assembly right side up, bolted the mount into place, installed the new belt onto the large flywheel, attached the belt tension spring, plugged in the wiring harness and ran a rinse cycle. No leaks. Good as new. Yes. It took a little longer than expected. But it was alot cheaper than having a service man do it.
Unhooked the idler pully spring, removed the 2 hoses from the pump outlets, unhooked the idler pulley srring to slaken the drive belt tension, removed 4 bolts from the motor mount to drop the motor, and slipped the drive belt off the transmission pulley.
Removed 3 torx screws that secure the pump. The pump was stuck to the motor motor shaft from corrosion and had to knock the pump off with a hammer. Reassembly was a breeze.
The most serious problem I had was a black widow spider lurking under the transmission pulley. Never did get it!
We noticed that water was on the ground of the laundry room. We initially thought that the washer was leaking. Realized that the washer was going on the spin cycle without draining the water which caused the water the slosh over the edges and then leak on the floor. Well, I had to remove all the wet clothes and suck the water out with a shop vaccuum-this actually took most of the time. After taking the front of the washer off, we noticed the water pump was stripped out. After removing the pump, we then noticed one of our kid's socks jammed in the pump. How the sock got there is still a mistery. We found the replacement part on PartSelect and ordering was easy and fast. Thanks. We're washing clothes again.
Blanket jambed drum, belt kept turning burned belt and pump
Unpluged washer, turned off water supply, removed front covers, removed spring on right side to allow drum to lean over, removed the 2 hoses from pump, removed motor (4 bolts), removed 3 screws holding pump. Installed a new belt and replaced the pump. I replaced the hoses on the pump, replaced the spring, and turned on the water, plugged in the washer, turned it on and hoped for the best. Worked fine, no leaks or problems.
My washer wouldn't agitate and there was a rubber burning smell
I was able to remove the belt because it was worn through. However, I was unable to remove the pump as described in the instructions because I was unable to get my torq wrench to the bolts. I ended up having a repairman come in.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer Wouldn't Turn On
Found out that these switches go from time to time and are usually the culprit when the washer won't operate. Opened the cabinet facing. Warning: there are plenty of YouTube videos on opening Maytag washers. None helped me with this model. I ended up finding the screws to open near the floor on front. Once it's opened, just replace the faulty switch, reconnect and you're in business. Getting the washer opened was about the hardest part of this repair. Total cost: Less than $30.
Wow! My husband and I researched the problem online and ordered the part after reading from others how to take the machine apart. We are very unhandy, so we felt quite an accomplishment fixing the drain hose with rubber elbow ourselves! Thank you for the diagrams that so clearly showed the part we needed to order.
Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.
remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.
Although the Maytag website no longer had a repair manual in their database, I was able to locate one fairly easily online. After removing the motor/washer pump, it was easy to remove the 3 screws holding the washer pump to the motor. Unfortunately, it turned out the motor hub shaft had corroded and removing the pump needed some ... persuasion. Patience and a rubber mallet eventually separated the water pump from the motor. Re-installing went quickly and, so far, no leaks and the washing machine has not started walking across the floor.
Removed the tension spring from the belt retention belt, removed the belt from the large pulley in the back of the washer, removed the 4 bolts holding in the motor and washer pump, removed wiring harness, disconnected the inlet and outlet hoses from the pump and pulled out the motor and the washer pump. Turned the motor over and using the Torx driver (#20) removed the 3 bolts holding on the pump. Gently wiggled and pried the washer pump off of the motor, replaced the pump and tightened down the Torx bolts carefully so the pump didn't crack or break it is just plastic, but had to be sure the pump was seated tightly so the pump would fit back into place and also so it wouldn't leak, after making sure it was tightly attached I reversed the process to put it back together.
