took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.
At first thought I was taking out some insulation but. "Clamp" just slid off and was very easy to install! Finding the right size socket took longer than the repair!
a plug on the element broke off while cleaning and replacing
Absolutely no tools required for this task. Simply align the prongs to the female portion on the stove top. Carefully push in until the element is in place then line up with the drip pan slot. No instructions are necessary!!
Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to swap out the parts and... success! Don't forget to turn off the circuit breaker before starting repairs.
1)Unscrewed old baking element from wall of oven 2)Detached old baking element from wires 3)Attached new baking element to wires 4)Screwed new baking element to wall of oven 5)Turned on oven
Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.
The bake element caught on fire. I needed to replace the burner..
All I had to do was just unscrew the bolts,pull out the old one, and put the new one on its metal clips and then rebolt.So easy and I know I would have had to pay much more then what I did for the part..This place is super.I ordered my part one day, and it was there the next...Sandy
Instead of flipping circuit breaker, we pulled the oven away from the wall and unplugged it. Used socket wrench to loosen screws of bracket holding old element onto the back oven wall, then gently pulled element until connecting wires appeared. Removed the 'clips' attached to the old element prongs and discarded old element. Reattached the 'clips' to new element prongs, then gently pushed prongs into back into oven wall until the bracket was flush with the wall. Used socket wrench to screw and tighten the bracket into place. Plugged in the oven and tested the new element to make sure it worked. The whole process took only a few minutes.....it took longer to clean the oven before installing the new element.
Easy Repair. Remove the storage draw under the oven. It lifts out. Lift oven door off of hinges. Remove 3 screws & unhook the spring. Reverse the procedure with the new hinge. Good as new.
After reading the other DIY's directions, we explored how to remove oven door. When the part came in, my sister who was visiting, removed the oven door (30seconds), removed bottom drawer (30 seconds), noted where spring was attached, took off screws and spring, installed new hinge with roller, took a minute to decide if the new hinge came through the back or the front (front), she reattached the spring and screws. Put door back on and then struggles to put the drawer back into place. Total time less than 5 mintues, most time spent on returning bottom drawer to its home. Thanks part select for helping me not burn my self every time I try and get food out of the oven!!! I open the oven door all the way and am so delighted!!
Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.
I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven. I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.
I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.
I received the kit two days after I ordered it, opened it and installed the knobs in less than 3 minites. The knobs were exact matches for the broken ones. The stove top now looks great and I cannot understand why I waited so long to make this simple repair.
