Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the bake element went out
First I removed the two screws, then I pulled old element out, placed the new element in. Returned the screws in place. Very easy, cheaper to get online than anywhere else and was faster to get the part than anywhere else.
Turn power off, then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected new element, put screws back in and test.
First I removed the two screwes that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires from the old element, then I connected the two wires to the new oven heating element. Pushed the unit back in place and reinstalled the two screws that hold it in place.( ALL Done)
Made sure that "Breaker" for oven is in the off positon.
Opened oven door to the first "stay open" position...lifted door straight up...and off of the hinges....which removes the door....and allows easier access to oven.
Removed oven racks
Removed two philips head
Pulled burned out element toward the front of the oven.....exposing the two connector wires.
Used pliers to pull wire connectors from burner element connectors.
Reversed the order of this process....to install new element.
I removed the screws that hold the element in place . Pulled the element out enough to disconnect the two wires . I then connected the new wires and pushed in the element . I finished off by screwing the bolts back in place.. Voila!!!!!!! I was in business once more! The part arrived within 48 hours and was very reasonably priced
Backed out two screws, disconnected two wires from faulty element, connected wires to new element, screwed back into place. (New element was ordered by phone and received the next day.)
Turn off the oven's breaker. Remove oven grates. Unscrew two screws holding in the bake element. Slowly pull the bake element out a few inches. Using pliers, CAREFULLY unattach the connectors from the ends of the bake element. DO NOT FORCE OR CRUSH THE CONNECTORS. Using your hands only, attach the connectors to the ends of the new bake element. Re-insert the element into the back of the oven. Re-insert the screws to attach the new element to the back of the oven. Turn the breaker back on. Turn the oven on bake to test the element. Go have a beer to congratulate yourself on saving $75 or more. Should take about 10 minutes if you're proceeding slowly & carefully. It'll take 2 minutes if you're reckless and get lucky, but it'll take 2+ hours if you're reckless and all goes wrong, causing you screw up the connectors and need to go buy some plus crimpers, etc.
Used screwdriver to unfasten the old element from the oven frame. Then unplugged the two wire plugs from the back of the old element. Reversed the process to install the new. Couldn't have been any simpler.
First I made sure it was in fact the lower bake element that was broken. I turned the oven on & noted the element did not glow red. I also used a laser thermometer to verify the element was at "room temperature" for the room it was in (the oven - about 200 degrees, given what the upper bake element was contributing.) And close visual inspection showed that a section of te bake element had melted thru where something had recently spilled onto it. Swapping it out was easy - turn off the electrical breaker controlling the oven, unscrew the bake element, disconnect the electrical contacts to it (which required pliers, since they had been on a Looong time, and a little care to not use the pliers too hard & thus break the wires or contacts), then reverse the process to install the new element.
Simply remove two phillips screws, unplug and replug. Thanks to the quality parts I bought here it saved me $65.00 on the part alone. Locally $85.00 plus shipping. Thanks guys for your help.
