Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No heat after self clean
Killed the power to oven, removed oven from its enclosure (its heavy), removed back off oven and the part that needed to be replaced was right there. After that simply reverse the procedure. Honestly hardest part of whole job was remembering what i did with the screwdriver after my last home repair job. The oven is heavy you may need help.
I was able to convince a local mechanic that he could do this after watching it done four times. The most difficult part was unscrewing and taking out the oven to get to the back. He suggested since this has happened everytime I used the self-cleaning feature, that I cut a hole in the wall for easier access (tongue-in-cheek). The most difficult part was dealing with the extended warranty service plan - this is covered, but they could not find a technician to do this. Then I found out they don't pay mileage so who would want to come out to a rural ND ranch to repair an oven?
control panel quit working, ovens would not operate
Contacted repair person on line and explained the problem. Person suggested testing the thermal fuse. Checked for continuity and there was none indicating the fuse was blown. Ordered new part and installed. Everything working again. Only problem was that the new part did not have the same connection as the old one on one end. Made substitution and it worked.
I found several posts about Whirlpool/KitchenAid ovens having this problem and most of the time this required a replacement of the thermal fuse. Other than the large number of screws to remove the oven and the sheet metal coverings, replacing the fuse was mostly about waiting to get the part. If I had a local dealer with the fuse, I probably could have been baking Deep Dark Chocolate Cheesecake that same evening. Even so, this particular repair should be left to those familiar with doing moderate-level handyman type repairs. You have to make sure the breaker is off and beware of the sharp edges on sheet metal. Fortunately, the fuse was easy to find using online documentation for my model. Part Select was very helpful when my original order did not arrive. Their customer service was great!
Turn off power at the breaker panel; remove oven door (see instructions in owners manual) and racks. Take out the 2 screws holding the element to roof of oven; next remove the 2 screws attaching the element at the rear of the oven; pull out element and disconnect wires. Attach new element to the wires and replace the 2 screws holding element to roof of oven. Next replace to 2 screws attaching element to the rear wall. Replace oven racks and door and turn power back on.
Removed trim strip from each side of oven, removed one screw from each side hat held oven in place and slid oven out of wall. Finally found the thermostat located on the back side of the oven after removing the sheet metal on back. replaced the thermostat and reversed the procedure. Only difficult part was locating the thermostat. I thought it was on top, when in fact it was on the back. Pretty easy, really, and saved some cash in the process.
Took out the 2 screws and removed 2 wires connected to old element, put on new one. Did this all in about 5-10 minutes. Hubby didn't even have to help!
I am not a big do-it-yourselfer, so maybe I might have found this more difficult than expected. When I first looked at the oven before ordering the part, I saw a couple of screws and it seemed like an easy task. However, I found that I had to remove to whole door first, which was actually easy. Then I started to remove the case. Then I removed several layers of a puzzle. Oven door had 3 pieces of glass and 3 metal brackets. The installation video was for a completely different oven. Although I got out the broken glass easily, I had difficulty reassembling. The oven diagram for the parts was even deceiving. I had to involve my spouse and after an hour of cursing everything, we finally managed to get the thing back together. Whoever designed this oven must have been a deranged German scientist. However, everything is back to normal and I probably saved a couple hundred bucks for a repairman.
Wall Oven door wouldn't close completely and when opened it wasn't level.
Because of the complexity of this door I video-taped my disassembly of the door to make sure I was able to put it all back together again (self-cleaning oven). Original order from PartSelect.com of 2 replacement hinges and a gasket worked only 3 months (the hinges) and the door again wouldn't close. I tried a couple dozen times to remove and put the door back on to no avail. It was my opinion that the original hinges were defective and I called PartSelect.com again. By this time I had removed the hinges (the first set purchased) and noticed the metal was "soft" and had sharp edges in a couple of areas where the hinge hook into the oven. When the replacement hinges arrived (the 1st two purchased came with a 1-year warranty) I compared the 2 new ones with the 2 first purchased and they were slightly different. I once again installed the new hinges, tightened all the screws, and the oven door immediately fell into place and is working perfectly. I have no idea why the first two new hinges worked for only 3 months and then the door once again wouldn't close but the two new replacements from PartSelect.com are working perfectly now. I am disappointed I was charged shipping for the 2nd set of hinges while they were covered under warranty. I do feel that because the 1st set were defective and under warranty I should not have been charged shipping of the 2nd set of hinges.
The only difficult part of this repair was figuring out how to get the oven door off. Most instructions advise you to flip the hinge locking clips, then lift off the door. But this oven does not have hinge locking clips. What it has is holes in the hinges, just behind the hinge pins. To get the door off, you need to open the door and insert some 3/16' pins in those holes, then close the door and lift it off. I almost got this right the first time, but I used 1/8" pins, and they didn't work, too small. It took me a long time to figure out to use bigger pins. Once the door is off, it's just a few Philips screws to work your way down to the glass. There are 4 layers of glass in this door.
The oven door would not fully close allowing some heat to escape. This was the result of the springs weakening over the past ten years.
When the oven is installed, there are two pins on the replacement hinges that are removed. If you were like me, you tossed these pins so you need to take a large nail and cut a 3/8" of material to replace these pins. This will allow the door to be removed when you open it half way. This is the most difficult part of the repair since you need to carefully pull the door off and a precise angle with an upward pull from the bottom. You will notice the new hinges have these pins so you can also try to get some new pins at a hardwire store that are similar. Next, you need to careful set the oven door down on a smooth work area and remove all of the philip head screws. The front of the door will be remove from the inside door piece by slipping it up a little when the screws are removed. The two screws that are on the inside panel hold the hinges. Take note of how you remove these since you will do just the reverse in putting in the new hinges. It would be a good idea to take the glass section off and clean it if you want to take on the extra challenge but you need to be very careful not to break these and that you put them back that same way it was removed. Now that you have it all put back together, you simply install the door back the way it was removed and then you can open it all of the way down to remove the pins in the hinges. Now would be a good time to put these pins in a save place with the rest of your paperwork for any further removal.
I read all the repairs. Turned off power to oven. Was ready to clamp clips so the don't fall behind oven and Crap!! One clip popped off so easy, it went behind insulation. Had to pull oven out. Put wire through, connected everything. Turned power on and oven and broiler work great.
I followed these instructions put in by a fellow customer. These were very helpful. Just make sure the glass is finger print free before you put it all back together. My time was 30 minutes end to end. =========================== The first thing I did was to remove the oven door by releasing the two latches on the hinges (by hand). I then raised the door toward the vertical position and lifted up. The hinges slide out of the oven housing. I laid the door, inside face up on my island counter top. This ensures that none of the parts will fall when disassembling the door. Next I unscrewed the screws 4 top and bottom and four on the inside face. This releases the frame from the front housing. Lift the frame off the door, exposing the glass pieces. Lift off the broken inside glass and place the new piece in the glass retaining housing. Replace the outside frame and replace all screws. Take door back over to oven and slide hinge bottoms back into slots on oven. Rotate to horizontal position and flip latches back to locked position. Total time was about 10 minutes mainly because I was curious how the door was constructed and I poked around while it was disassembled
removed two screws in rear of oven. pulled old element out replaced new one. piece of cake.I am a 70 year old female. if i can do it anyone can.thank you for your swift delivery.
