RB262PXAQ4 Whirlpool Range - Instructions

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Excellent experience with Part Select. Ordered the part on Sunday and received it on Tuesday. Super speedy service and easy installation.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.

removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair

The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.

Parts package contained no instructions. Found all instructions on internet. I used Phillips head to remove two screws on anchor plate of Long Oven Sensor. Located at upper left, back corner of oven; access to screws is not simple/easy. Screws back out w/o difficulty. Pull/extract sensor harness through hole[back of oven] which required pushing aside insulation. The harness barely fits thru hole in oven back metal wall; I recommend using needle nose pliers ( which I ended up doing ) for ease of extraction. Disconnect harness plastic interlok clips. Perfect reconnection of new clip harness with ease. Reverse procedure to complete installation/repair. Done in just over 35 minutes due to wrestling with harness extraction through minimal hole opening. Failure occurred on Thanksgiving Day with 22lbs turkey in oven. Top of turkey contacted sensor tip which eventually caused sensor fault; result was scorched upper breast and oven shut down [safety by design]. Cook top was still operative; clock and all readings on digital control panel ceased. With new 'long oven sensor' installed - good as new. Will be sure to buy turkey(s) under 20lbs in future. Jim in Seattle

Removed the back of the stove, un-pluged the sensor wires, removed the sensor from inside the oven. installed the new sensor, pluged in the wires, and replaced the back of the stove. A phillips screwdriver was the only tool needed.

I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fish out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.