Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven on range did not work properly
My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.
Oven not holding a consistant temperature. Found the replacement part easily on you website.Thanks to your photo.
First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.
lift door off and remove racks take out old sensor. one word of advise when pulling old sensor out tie a string around connector coming out of oven if it slips out of yor hand it could fall through hole iif you dont have a string attached you pull the whole oven out of wall to acess it
Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...
Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.
When inspecting the back of my oven I noticed the cable had been pushed under (my guess from the mouse I found electrocuted where the power lines come in) and was touching one of the element prongs which burned the covering.
Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.
GE WB44T10086 Range Convection Element AP4358533 PS2321875 interrupted
after you disconnect the direct breakers and open the oven: 1. remove the first 4 screws and the fan's cover 2. remove the short screws from element convection assembly 3. gently pool both wires and disconnect the old element (two terminals) 4. carefully insert the terminals in the new element. 5. re-screw the short 4 screws (better to buy new ones with the assembly) They are available but sold separated. 6. fix back the fan cover, re-connect the breakers and that's it!
Very simple. Remove one screw and carefully pull the sensor until you see the connection point. Remove the old one and snap the new one in and guide the wire back and reassemble the screw. Be sure to remove the oven door for easy access.
This door required a lot more screws to be removed in order to remove the inside window assembly. I counted a total of 19 screws. That is why the estimated time is 30-60 minutes.
- remove door from range following the basic guide to removing any range door. - place door on work surface with the outside facing down. - remove three 1/4 socket screws from bottom and two star screws on top. - Flip door over, remove outer door panel and set aside. - There will be a separate pane of glass that needs to be removed. Remove 1/4 socket screws holding glass and set aside. - Slide door over your work surface edge so you can remove the star screws holding the door hinges (from underneath). You could flip the door over but the door would have to be flipped back once the hinges were removed. - Remove the remaining 1/4 screws holding the aluminum shielding. - Remove the shielding being careful not to disturb the insulation around the window. - Remove the damaged window. Take note of the writing and orientation on the aluminum window frame. (upper right if hinges were on the bottom) - Set the new window in its place. - Reverse the process by replacing the aluminum shield, hinges, than internal glass pane. - Set outer door on top and holding everything together, flip door. - Tighten the two star screws on top and the three 1/4 socket screws on the bottom. - Replace door. Don't forget to lift up those hinge tabs before trying to close the door. All done. Pat yourself on the back for a job well done.
had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yum.
Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Theaded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.
