Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
washer making pounding and rocking sound
Took a screwdriver and pried up the top of washer, then reached in and unscrewed the front two screws that allowed the front to be lifted off. Removed two screws on lower right side that allowed us to pry open right side of washer. There are six springs along the bottom of washer that keep the tub stable and keep it from bouncing against sides while in spin mode. One of the springs broke and needed to be replaced. Off course it was the one that was in the far back and the hardest to get too. But by prying open the right side it was reachable. The wife pushed against the tub to make the spring stretch a little less but still was too difficult. We took the advice of another home repair guy and put quarters in the spring (about $1.75 worth) to make it stretch out, then it was simple to connect the two ends, remove the quarters and voila....it was done. Screwed theright side back on, but the minimum order on the springs was six and the others seemed fine, we just put the other five inside the washer cabinet, replaced the front panel, reset the clamps on top of the front panel, slammed the top down and we were back in business. The parts including shipping was a little over $10.00. So I am sure we saved at least $140 repair job.
Lid switch had deteriated over time and no longer made contact
removed the screw holding the actuator, ordered the new part and replaced it when it arrived. Shipping was really fast and I even received it one day early.
First push inner tub to left rear, all the way, and unscrew hinge from inside of tub. repeat same on right side. lift cover off and unscrew other half of hinge off cover, both sides.reverse procedures and your done. Note: always replace both hinge's new while you have it apart.
For safety I Unplugged the machine Tipped machine back and removed the belt. Rotated the motor by hand and all is well there. Rotated the water pump by hand and a grinding sound appeared. I Let the machine down . Using a hard object , 1/16th of an inch thick, I slide it between the front edge of the lid and the front panel unlocking the clips ( one on the right side and one on the left side ) holding the lid down. I then tipped the lid up and removed the 2 screws holding the front panel on. Lifted the front panel off of the clips on the bottom end of panel. Using a nut driver I removed the 3 bolts holding the pump to the frame. Then with a pliers I removed the clips holding the 2 hoses. With a pan to catch the water I removed the hoses and drained them into the pan. I then took my machine model number and went to the internet in search of a new water pump. After checking several sites with no success, I come upon the site for PartSelect.Com. With the excellent search method on the site I was able to quickly find the part I needed. I placed my order (10pm) on a Tuesday night and a short time later I received an email letting me know they had my order. On Wednesday I received an email letting me know they had shipped my order. On Friday the order had arrived. I removed the new pump from the box and inspected it . Every thing looks great. I placed the pump into its mount on machine and bolted it down. Attached the 2 hoses, put the front panel back on and tipped the top down into place. Pushed machine into place, plugged it in and fired it up. I now have a quiet running machine again. Thank You to PartSelect.com for the quick response to my
tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!
Removed the waterlines. Set the ends in a small pan or bucket to catch the water.Do the same with the drain line. Keep an old towell handy as water will drain out of the drain pump when you remove the drain hose. Removed the back panel. Use a flat bladed screw driver to pop the top off the two clips in front holding the top down. Lift the top and pull the two screws which holds the front in place. Remove the front and set aside. Underneath, use gloves and the screw driver to remove the six springs by placing the screwdriver through the top hook end about an inch and with both hands lift the spring off. Carefull not to let the blade slip off and bust your knuckles on something,hence the gloves. Lean the machine over and walk the belt off the pulley. Disconnect the small tube in the back left corner from the drum and lift the unit out from the top. Set the drum on it's top and loosen the six screws under the big pulley just enough to pull the snubber out. Replace new snubber, tighten screws. Set drum back in place and reattach springs. Lean unit over and replace belt. Reconnect the small tube, back left corner. Replace the front panel and top. Connect the drain line and replace the rear panel. Connect waterlines and check for leaks. I went ahead and replaced all springs. I recommend replacing the belt while your at it. I'm wishing I would have. It runs like new, gets more water out on the spin cycle and the dryer dosn't take as long to dry the clothes.
First I removed the bolt and removed the old agitator and post assembly then I put the new agitator and post assembly in place and tightened the bolt. It was so easy, when I called the manufacturer they wanted to send out a technician, but thanks to Parts Select I fixed the problem without spending alot of money and without the hassle.
Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.
After replacing the tub to pump hose, I adjusted the feet on the washer. Apparently, the main pulley sits so low on these washers that it ground into the floor and stripped out the thrust bearing. I ordered the new thrust bearing clip and put it in the evening I received it. The instructions it came with were very helpful and it was simple to reassemble. Up until the last piece - the retaining clip. The majority of the repair time was spent replacing that clip. If there is a tool that makes the job easier, I didn't have it. I finally got it on with two flathead screwdrivers prying the shaft out while I wedged one corner of the clip in the groove.
Water wouldn't shutoff. Agitator would pop up and stop agitating
Opened up washer, found vacuum hose was broken and replaced it. Removed agitator with a couple extensions and a socket wrench. Found agitator part was worn out and replaced it. The best part was how great PartSelect made it so incredibly simple and easy to find the right part. I'm now a customer for life. Kudos PartSelect.
I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!
first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy
I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.
The parts list and schematic made it easy to select the correct part that my wife and I believed was the problem. The plastic part was removed easily because it kept on popping off during the wash cycle of anything other than light low loads. The mechanism was useless. With the new piece/part inserted the machine got back to business as it should be. Plastic just wears out to quick. At least we have delayed a machine replacement.