NVLR223EH7WO Hotpoint Dryer - Instructions

Washer/dryer belongs to a friend. Originally, the problem was that the dryer wouldn’t heat, so I opened it up, and removed the drum thinking it might be the heating element. It wasn’t, and the ohm reading confirmed this. It turned out to be a burnt wire connector to the element ( unknown to me, and found out later, was that the start switch had remained continuously in the down position because the switch was pressed too far down and thus remained locked “on” in place under the surrounding cabinet frame. This, in my opinion, caused for a continual call for heat and thus burnt the wire.)

I replaced the burnt wire/connector and reassembled. Now the dryer would heat, but would only run if the start button was continually depressed. Let go of the button, and the dryer stopped.

Repair pros suggested a new start switch. I bought a new start switch along with a new interlock switch (it basically shuts off dryer if belt breaks because lack of a belt releases pressure on the pulley that keeps switch depressed.) Apparently they can go bad, too.

It turns out neither of these switches were bad. Instead, upon further inspection, after the first installation of the drum belt, the L-shaped bracket which holds the pulley for belt tension became dislocated from its correct position and was not allowing for the depression of the interlock switch, causing the dryer to “read” broken belt, and thus, not run.

I loosened the motor bracket to allow placing the bracket in the correct position. Reassembled and all was good.
PSA - almost every sheet metal edge is razor sharp.
In the process of returning parts. Now in the process of returning parts.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!

Unplug dryer, remove screws and panel. Take picture of dryer motor so you will put wires back the same way . Remove screws using Allen wrench, then unplug wires put the new motor on secure, then put wires back on. View the photo make sure the wires are the same. Then plug your dryer back up. And Happy drying..

I've experienced same symptoms on previous dryers over the last 30+ years, so I immediately ordered a rear drum bearing replacement kit from PartSelect. Perfect replacement parts for replacement of OEM parts.

1) After unplugging dryer, moved it to garage because of expected dust and lint deposits.
2) Removing two screws under from top lip allows top to lift and rotate off of dryer.
3) Removing two screws inside on both sides allows the front panel to be removed. Just remember to lift drum when you pull pannel off.
4) Best to take front panel off completely, so remove single screw on green ground wire at lower left and disconnect the white two wire connector (pull apart). Three wires need to come off of door switch (yellow/brown and white leading from the dryer inerds and one white to the drum light). Best to tag or remember where they connect. Otherwise, white from inerds goes to switch common, y/b goes to normally open and bulb white goes to normally closed terminals.
5) Get someone with really skinny arms to reach in to slide drum belt off of idler pulley. Otherwise, long sleeves are a necessity to keep from getting sliced to pieces on sheet metal edges.
6) Lift drum out and away from dryer frame. It's a pretty tight fit so get a helper to spread the side panels apart a bit.
7) Replace both bearing pin in drum and bearing socket in heater pan, following instructions that come with the parts or the video that is on the PartSelect website.

Didn't expect the drum slides and top drum slide support to be worn out, so I had to order them ASAP from PartSelect. The slides were totally gone and the support assemble was effectively toast. You might seriously consider replacing the slides and the lower felt when you try to fix the squeeks, since they are a major source of the noise and take an additional 2-3 minutes to replace.
8) Reassembly of the dryer is just doing the above steps in reverse. Best to clean out as much lint/dust as possible, since a clean dryer is an efficient dryer and we all want to make our "green" friends happy nowadays.

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

Took out interlock switch (two leads) and replaced with new one. As simple as that.

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new

remove the broken one and replace it with the new one

Easy repair, but did take a little longer than anticipated due to the extra cleaning that I did while the dryer was disassembled (highly recommend). First, unplug the power cord. Then, open the door, and locate the two screws in the upper corners, and remove. This will allow you to remove the top cover. Be careful and work the top panel up and down to loosen the control panel tabs, and set aside top panel. Next, remove the two screws located near the top on the inside of the front panel. Removing these two screws will allow you to lean the front panel forward, lift up, releasing the tabs holding the bottom of the panel. Be careful when you pull the front panel from the dryer as you will need to lift the drum off of the front bearing which is attached to the front panel as it is removed. You will also need to use your needle nose pliers to remove the wires prior to setting the panel aside. The wires are straight forward and power the light at the top, and the safety door switch. I always take a picture with my phone's camera just to validate when I re-connect them. Reaching underneath the drum you will be able to feel the belt and belt tensioner pulley. With both hands under the drum, use one hand to push the pulley to the right, releasing tension on the belt. Move the belt out of the groove, and let it hang freely. Now from the top of the drum, bump the drum to loosen, and remove from the cabinet. It is a tight fit, so you will need to spread the sides slightly in order to remove the drum. Next, remove the 3 screws holding the heat diffuser in the rear of the drum in order to remove the rear drum bearing. (Tip: It would be nice to have a helper hold the new drum bearing in place when starting the screws, and it also helped to tighten each a little at a time to keep the new bearing flat as it was drawn up next to the drum.) Tighten the screws holding the new bearing in place. Next, remove the 4 small screws holding the heating element housing to the rear of the dryer. (Tip: Rather than disconnecting the wires, I used a bent coat hanger to hold the housing while I removed the bearing retainer and clip from the rear of the housing.) Remove the 4 screws holding the bearing retainer and clip, and replace with you new part, paying close attention to the clip's position, and tighten. Replace the housing to the rear of the dryer. (Tip: Now is a good time to familiarize yourself with the belt and tensioner pulley for reassembly. Also, it may be a good idea to look at your belt, and replace as needed.) Next, reinstall the drum and insert the new bearing shaft into the new bearing housing. Using both hands again, reach underneath the drum, locate the tensioner pulley, and belt. Push the tensioner pulley over to the right, and move belt over the pulley on the motor, and behind the tensioner pulley. The belt should be tight. If not, inspect to ensure that the belt is over the motor pulley, and the tensioner pulley. Next step is to reinstall the front panel. I also spent the extra money and replaced the front drum bearing, and slides. Please note that the green slides are on top, and the white slides are on the bottom. Lift the panel over the tabs, lean forward while lifting the tub, resting the tub on the front bearing. Reinstall two screws in the upper corners, and tighten the front panel back in place. Now is a good time to turn the drum to ensure that the belt is in place, and that the drum turns correctly. (Tip: If your dryer is equipped with a light, you may also want to replace the bulb in the front panel (if needed) prior to attaching the front panel.) Reinstall the top panel by aligning the tabs in the control panel with the top panel, being careful not to bend the tabs. Next, open the front door and use the 2 long screws to reattach the top panel to the front panel. Plug in power cord.

Pull the two scews to release the top of the cabinet. Pull the two screws to release the face of the cabinet and tilt out.
Take the old slide out and install the new ones.
Put it back together.
No more squeeks
My wife thinks I'm a genius...

Opened dryer door and removed two screws that held front of top panel on. Lifted top panel off and removed two screws that held front panel to side panels. Tipped front panel forward and replaced all four slides. Cleaned everything off and put back together. Works great again. Thanks for this site and for others that have done these repairs before and posted their stories.