Washer basket off-center and wobbling during spin cycle
Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.
After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spring bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring. If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!
Changing the springs was a ...snap. The more delicate task was to figure out how to get to them; for this model, the back panel comes off (after removing 3 screws, the drain hose and drain hose plastic coupler, removing the 2 screws holding the control panel, pivoting the control panel and finally removing two spring clips. Also, the plastic water diverter takes a little bit of patience to be unhooked from its slots in the back panel as it will not slide out with the back panel. With the back panel off, the entire "shell" can be removed, exposing the guts. I twisted the tub to release the tension in the suspension springs and replaced them, one by one. Finally, the counterweight spring. I also lubed the support pads to allow for a "friendlier" leveling. Re-assemble, replace the old and cracked water supply hoses, and time for a beer and my girlfriend's obligatory OOOOHs and AAAAHs... All in all (cleanup and test included..) about one hour.
While taking apart my washing machine to clean the plastic basket I discovered the 3 main seals down the agitator were completely disintegrated and water was leaking onto the motor and onto the floor. The seals are a tight fit but slide into place easily with lubrication. When putting everything back together a bit of lubrication will be necessary as well. The leak is gone and my nearly 30 year old washer is working as well as the day it came off of the assembly line.
Broken water inlet syphon combined with missing feet was causing water to spill out of the washer
I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.
diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.
The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.
I turned the washer on its side and felt where the leak was on the pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.
I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
After reading other comments about lid switch replacement , I knew the front of the control panel would move forward and lift off. Although none of the descriptions mention the steel clips that were also use to hold the cover down. It does take quite a bit of presure to pry these up and loose before panel would move forward. Would recomend putting tape on both washer and screwdriver to protect washer.
Washer would not start adjutating unless I opened and closed the lid a few times.
Unplugged the main power. Removed the 2 screws in the back and top of the control panel. Pulled control panel forward and tipped towards me to remove from top of washer. Removed the ground wire screw with a socket/ratchet. Removed the switch by pressing the tap inwards. The tab was brittle and broke. Replaced the switch, ground wire with screw and the control panel. I notice that the 2 screws which secure the switch lever/hinge to the lid were loose. These 2 loose screws were actually the problem in the first place. The loose lever was not making good contact with the switch. I think the switch was actually fine but since I broke the tab on the switch I needed to replace it anyhow. Plugged in power cord and washed a load.
Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you