I viewed the YTube Video that showed exactly how to remove the door and all the other parts for replacement. Excellent video shows and explains how to remove, replace, and re-attach the handle and the door.
1. OPEN THE OVEN DOOR TO THE FIRST STOP, PULL UPWARD TO REMOVE, ( IT WILL LIFT RIGHT OFF) 2. LAY OVEN DOOR ON A FLAT SURFACE ( HANDLE DOWN AND HANGING OFF SURFACE) WITH A TOWEL TO PROTECT THE GLASS. 3. REMOVE ALL SCREWS AROUND THE PERIMETER OF THE DOOR.. 4. CAREFULLY SEPARATE THE DOOR FRONT AND BOTTOM BRACKET BY SLIDING AWAY FROM THE MAIN DOOR INNER-ASSEMBLY, ( THE FRONT GLASS IS HELD BY THE TOP CHANNEL. 5. TURN THE MAIN DOOR INNER ASSEMBLY OVER AND REMOVE THE HANDLE ASSEMBLY TWO ATTACHING BRACKETS. 6. REMOVE THE ATTACHING BRACKETS FROM THE HANDLE AND ATTACH TO THE NEW HANDLE. 7. THE DOOR GLASSES CAN NOW BE CLEANED 8. ATTACH THE NEW HANDLE ASSEMBLY 9. REASSEMBLE IN REVERSE ORDER. ( BE CAREFUL WHEN SLIDING FRONT DOOR GLASS INTO THE TOP DOOR CHANNEL}
You Tube!!! Didn’t find my exact oven, but watching a couple of videos was extremely helpful. Replacing the igniter was basically simple, but since it was a first for me, I took my time. Probably saved $200. The part was just over $100.
moved stove away from the wall, Disconnected power, Removed 2 screws on the access panel and removed panel. Disconnected qwick release conections on heat sensor and ignitor, Removed oven door and burner cover to expose ignitor, removed 2 screws to remove ignitor and replaced ignitor. Removed 2 screws and removed sensor, replaced sensor. Reconnected qwick conects on sensor and ignitor. Replaced oven door, burner cover and access panel and checked out. Checks OK !
Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.
Door gasket was hard and brittle from baked-on grease - heat leaking around door
Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.
The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.
My 4 year old son managed to break the oven door glass. The repair man asked for $175 to fix it I had ordered the door kit from Part Select and it arrived earlier than promised. Fifteen minutes later I had it in place. The cost $49.64 Thanks Part Select,
door seal contaminated by a boil-over, not flexible
From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.
Remove sides and face of oven door by sliding down from under the oven handle trim.
Remove screws on 2nd light of glass and set aside.
Now you are at the inner door panes. their should be two in an insulated type unit.
Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.
Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)
reassemble door as it came apart carefull not to over tighten the screws, they strip easy.
1. Lifted the oven door off the hinge mechanisms. 2. Removed the screws holding the bottom front glass support bracket. 3. Removed the bracket and the remaining broken glass from that support bracket. 4. Cleaned the new glass front with Glass Cleaner and slid it into the top support bracket. 5. Slid the previously removed bracket onto the glass and positioned that bracket back onto the oven door. 6. Re-installed the screws to hold the bracket and the new glass in place. 7. Slid the oven door back onto the hinge mechanisms on the stove.
So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is like new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.
