Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replace igniters
Watched u tube video as supplied and followed instructions. Had trouble getting burners off so cleaned around edge of burners with fine bladed knife as suggested by other forum user and used oil filter type wrench to remove burner. There are three bumps on burner that hold it in place so need to turn anti clockwise to remove.
Removed door and bottom oven pan to expose igniter. It was held in place by two sheet metal screws. Tried to back them out but due to heat damage , they stripped. I used my versa tool with a metal blade to cut the screws. I removed the old igniter and disconnected the plug, after I guided it out from the insulation. I installed the new igniter with two new self tapping screws after I connected the plug and guided it back through the insulation. Reinstalled the oven pan and door. I set the oven to 350° and the new igniter worked. Wife is happy and I saved the repairman fees.
First I removed the oven racks, then the bottom cover over the burner. I then unscrewed the two screws holding the igniter on to the bracket on the burner tube. I then removed the storage drawer and loosened the two screws holding the metal shield in place. I then unclipped the electrical connection to the ignitor and pushed it up past the insulation. I then went back into the oven and pulled the wires and connector through. The old igniter was out!
Installation of the new one was just as easy. Screwed the new igniter onto the backet, stuck the electrical connector through the hole in the back of the burner tube, and connected it. I then replaced the shield and the storage drawer, replaced the bottom pan over the burner tube and the racks. The stove works perfectly and my wife is happy. The job couldn't be easier.
I expected to see a thermocouple and a heating element next to the gas valve but after reviewing other PartSelect stories from people with a similar problem I realized that the heating element also serves as the switch. Apparently as the heating element is energized by the oven control it draws more amps. The gas valve is allowed to open at a specific level corresponding to a sufficiently glowing heating element. I ordered a new heating element. The part received was made up of two pieces. The heating element and the metal mounting bracket. The element was identical but assumingly due to the age of my stove the bracket was slightly different. Fortunatly I was able to slide the new element into the old bracket. The only other obsticle was that the new element came with a two conductor connector and the old was installed with ceramic wire nuts. The connector was cut off and the ceramic wire nuts were reused. Its working fine.
I removed the oven racks, the bottom of the stove and a v-shaped cover that was over the heating element. The old gas ignitor screwed off easily after I put W-D 40 on the nuts. I un ooked the old gas igniter and replaced it with the new one. The oven lit immediately after I replaced everything. I am very proud of my self, I feel like a femal Bob Villa. I almost bought a new range. Boy am I happy!
I first removed the screws inside the oven,let the tube that the flames come out of hang down,removed the screws from the igniter. Then I took the cover off the back of the stove and unplugged the old igniter and plugged in the new one. I put all screws back and put every thing back in place and the oven has been heating up every since. Thank you parts select. My husband is a otr trucker and won't be home until the 20th of this month. One less item on his "honey do list".
Removed stove top, 3 of 4 sealed burners were a bugger to get loose, then took out two screw that held thermostat to front of stove, then removed thermostat sensor from the brackets in oven, then removed sensor from oven up thru stove top, and out. Reinstalled new unit, test ran. Oven still wouldn't heat :( Back to PartSelect to order igniter. Got it in 2 days, put IT in, and we're back in bizness! Spent more time cleaning stove than repairing it. Thanks, PS!
Removed oven door by opening slightly and lifting straight up. Pulled out racks and removed bottom of oven. Unscrewed wingnut and removed burner shield. Removed 2 screws that hold igniter and unplugged the connection. Reverse the procedure to put it all back together. Be patient, it takes a few moments for it to begin heating when you first turn it on. So easy a woman can do it ! I know,(I am one).