Dryer was very loud and sounded like it was scraping
Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!
Gas Dryer Runs With Heat for Less Than 5 minutes, Timer Won't Advance in Autodry
My gas dryer would run with heat for 5 minutes in all settings, but kick off and not heat again. Timer would not advance in autodry. Thought it was the cycling thermostat, so replaced that, but did not solve the issue. Ordered the coils, and cleaned out heavily clogged lint from bottom of lint trap, especially right above the fan motor at the bottom of the trap. Received the coils, opened the top and front, took out drum, and replaced the coils. The replacement took less than 2 minutes. Be careful putting the drum back on to make sure the felt is not caught inside the drum. You can give it a spin to make sure. Wear gloves, as I cut myself up pretty good on the edges of the dryer body. The inside of my dryer looks like a crime scene! Anyway, I put it back together, and it runs great. Solved the timer advance issue in autodry, and the heat kicks on and off when it is supposed to. Good luck! Thanks Part Select!
I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Take pictures along the way. 1. Remove lower front panel using screwdriver to lift up on tabs on top of panel. 2. remove door 3. unplug moisture sensor plugs 4. remove lint trap 5. on back of dryer, remove screws holding upper lid 6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on 7. remove the front panel screws mentioned in step 6. 8. Remove lower front panel screws 9. remove front panel 10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys) 11. slide out tumbling drum 12. with drum removed, use socket wrench and socket to remove old idler pulley. 13. install new idler pulley 14. reinstall tumbling drum 15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley. 16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly. 17. Reinstall front panel 18 slide top panel back into place and secure with screws from back 19. reinstall door 20. reattach moisture sensor plugs 21. reinstall lower panel
Desarme la puerta y coloque la nueva con mucha facilidad, nunca reparé un electrodoméstico antes de este, seguí el diagrama que encontré en el sitio para elegir la pieza que se rompio
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
Found on your site the top two causes of a Dryer not getting hot enough and ordered those parts ( which were delivered quickly).Removed the top two screws that hold the front of the dryer that gives access to the coils and flame sensor assembly after lifting up the top.It took more time to clean up all the lint than to replace the parts.Dryer works great!
The design of the dryer did not make the conversion easy, I had to disassemble the entire front end, top and remove the drum. The kit included a new spud that's it (22.00?). Anyway the gas valve is convertible from NAT to LP only requires turning a portion of the valve about 25 degrees. I managed with a screwdriver as I could not locate my snap ring pliers(just moved). The directions were spot on, read them through once before you start.
I had two dryers, one was gas and the other was electric. The electric stopped heating. So I rolled out the gas dryer, but it was setup for natural gas and at this location, I only have propane. So I changed the jets to work with propane, in the process I broke the igniter, so I replaced that and that made the propane one work. Armed with the knowledge from that job, I took the electric dryer apart located the thermostat and replaced that and low and behold I have two working dryers. One for now and one for an emergency. I only have four screws left over!!!! Jim Cooke
Doing my home work, I was told if I was "handy with my hands" I could do the work. Start to finish required 3+ hours. The instructions were not specific to my unit therefore, I had to "guess". My first surprise was encountered on step 2 - removing the top. My top was attached to the "brains" of the drier and therefore could not be removed. I actually had to disconnect the brains to remove the top. My second surprise was that I had to remove just about everything before I could get to the vent, which by the way, was simple. I finally accomplished the task, but....
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
16 of 43 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gas drier would not heat
i read some of previous customer problems and fixes pulled the front cover off found coil's location when i turned on drier you could see the ignitor getv hot but burner would not ignite unless i put a little pressure on secondary coil when i let go of coil flame would go out. ordered 'M' series new style coil kit came in in about three days installed parts drier workng good i would reuse parts select agian thanks