Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Right side pantry end cap had a broken hinge pin
Looked at the new part to determine what I would need to remove the old part. It was very easy to figure out. I removed the old end cap by taking out the screws. Once the screws were out I popped the side of the end cap off. There is a horizontal piece along the back wall that is connected to the end cap. On the left side of this piece of plastic there is a small tab that clicks into the back wall. On the right hand end cap there is a sliding lever which controls the air in the deli tray. This control is made of plastic and appears to be pretty fragile> By gently bending this lever I was able to remove the control lever and install it on the new end cap. In all it took me about 15 minutes to complete the entire job. Very easy.
First pull out bucket, then slide side plastic piece that hides wire harness on lower left side out.. Then pull /slide whole unit forward/out. Disconnect wire harness plug when doing so. Set old unit on table standing on end, put new unit right next to it. remove whole tray assembly from old unit, 3 screws on back. Use new wire harness that comes with new ice maker. put new tray assembly on end unit where the other came off. replace the three screws holding it to fan unit. remove on/off switch from old unit and put in new unit cover. Use small screw driver to remove old end switch cover. On off switch is pushed into place on new end cover. Purple wire on bottom plug and other on top. observe what you have and Just replace what you removed. Piece I did not use was flat plastic piece,flapper? This did not come with instructions, so basically I changed everything incl wire harness, put back together and put back in freezer. Ice bucket was full by next morning. Instructions and or video would have been nice. Tool;s used was a 1/4 in nut driver, small flat blade screwdriver.
Seal would not stay on, letting cold air out of ice maker - did not make ice.
The old plactic ring can be removed with flat bladed screw driver, starting on the right side prying it up worked best for me. The new seal snaps in only one way take your time to get it wright.
PartSelect Number PS8260210 Manufacturer Part Number W10583817
Tools used: Small 1/4 in nut driver Small flat blade screwdriver Needle nose pliers Flashlight Time: about 30 minutes
#1 Unplug the refrigerator.
#2 Pull out the ice bucket.
#3 Slide bottom left edge plastic cover that hides the wire harness out. (To do this you need a small screw driver to pry the front out a bit and to insert into the slot in the middle to unlock it, then pull forward. Be careful not to break).
#4 Disconnect wire harness. (Plug has a small catch in the middle you must press to pull apart).
#5 Pull the whole unit out. (To do this you need to pry a small catch on the left out, then pull. It may be tight since it’s been in there a while and there is a small rubber water tube protruding from the roof that it will rub against).
#6 Carefully empty any water still in the icemaker into the sink. (Try not to get any of the electrical components on the fan assembly wet. If you do, a blow dryer works well to dry out quickly).
#7 Put old unit on a large table and new unit / parts next to it.
#8 Remove ice maker and tray assembly from old unit, three screws on bottom of ice maker. (Do not confuse with the three screws holding the ice dispenser motor in place). Unplug wire harness, remove small funnel.
Replacement Parts Assembly - The next few steps get a bit tricky as you may need to do several things simultaneously.
#9 Route new wiring harness. Route under the plastic clips on the new plastic tray. (Black connector and switch wires run around the bottom left corner of the ice maker head to the front).
#10 Install the new water funnel. Loosely attach new tray assembly to new ice maker ensuring wire harness is routed properly. Plug in the wire harness connectors with the exception of the black connector and the O/I switch wires.
#11 Push loosely assembled unit onto fan assembly ensuring correct funnel seating. Secure the entire assembly by replacing the three screws.
#12 Connect the black connector to the ice maker head. (Match up the holes)
#13 Check your work. (If you forgot something or misrouted your wires you may need to take it apart and do it again).
#14 Remove O/I switch from old unit. (Use a small screw driver to pop out and needle nose pliers to carefully remove the connectors). CAUTION: Be very careful as these switch connectors are not very robust and can easily pull right out of the switch if not done very carefully. (Why a new unit doesn’t come with a new off/on switch is beyond me).
#15 Push O/I switch into place on new end cover. Install power wires.
#16 Carefully push the cover onto the head ensuring the cables do not bind or get pinched.
#17 Check your work.
#18 Install plastic flapper onto the control rod. (This takes a little study to get it on right).
#19 Install control rod/ flapper assembly into hole on the ice maker. (Note: Ensure rod is all the way in and that it also goes through the hole at the opposite end. The position seems a bit odd at first but after the ice maker cycles it will drop into position. This is needed to let the ice maker know when the ice bucket is full of ice).
#20 Carefully slide assembled icemaker into freezer. (Mine was tight but it will slowly pop into place). Ensure the catch pops back into place. Observe the rubber hose protruding from the roof, it should be directly over the small funnel.
#21 Reattach the wiring harness.
#22 Reinstall the wire harness cover.
#23 Flip the switch to on. ( O = OFF I = ON )
#24 Reinstall the Ice bucket.
#25 Plug in the refrigerator.
#26 Wait several hours and you should start getting ice.
Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar. Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars
We came home from a long vacation to discover a warm refrigerator with its contents in various stages of decay.
Turning the freezer thermostat to its warmest setting then back to cold generated clicks, and after a few tries the compressor started and cooled the refrigerator to its normal cold temperatures. But… later the compressor again failed to start, and everything warmed back up again. With persistence and turning the thermostat up and down several times a day, we could keep the fridge cold.
It was time to order parts. We needed a new start relay and capacitor for the compressor. For our Amana ARB2214CW a start relay (WP12555902) and capacitor (WP65889-4) were listed on the first page of the Partselect parts list for my refrigerator. I ordered them, received them, removed the old capacitor and start relay (which rattled when shaken). and prepared to install my new parts. The new start relay did not match the old. The old start relay fit my wiring which had a single plug with two small female spade connectors in the plug. The new start relay required wiring with two separate female spade connectors; one the normal size and one larger. Phone calls to Partselect and to Westinghouse shed no light on the discrepancy. On the second page of the Partselect parts list was a combination of a start relay and a capacitor (W10613606) that matched my electrical connector. I could see the connection in the photograph. I ordered it and it fit. Easy peazy. That fixed the compressor start problem. Every time the freezer thermostat clicked on, the compressor started. Success.
But… from our troubleshooting we now had a thermometer the freezer, and it was obvious that the temperature difference between the cold point where the thermostat turned the compressor off and the warm point where the thermostat restarted the compressor was much too wide. In addition, the knob was hard to turn and was sticky as it turned. Oiling it fixed the sticky knob problem but not the wide temperature difference problem. I ordered a new freezer thermostat (WP67003000), received it, installed it, and all is now fine with my refrigerator. The new thermostat was physically a little different from the original, but it fit and worked.
I returned the first compressor start relay and capacitor and received a refund including the shipping charge.
Right side endcap - drawer pin broke that the flip up top uses to pivot up and down
I removed the right side endcap and rear thermostat piece behind the pull out drawer. It was fairly quick, 3 screws on the exterior of the end cap and one screw holding in the drawer thermostat. The worst part was getting the thermostat control that connects the drawer thermostat control to the rear thermostat. After playing with the control rod I was able to to snap it in successfully to the endcap with the proper rod connection. The rear thermostat goes in first, then the endcap. Quick and easy. For $23 it would have cost over $150 to call a repair guy ($120 call charge plus parts). Thanks.
I brought you the exploded view of the crisper parts on your website and proceeded accordingly. Besides the three nuts holding the end cap to the frig interior wall the temperature adjustment linkage had to be disassembled on reassemblied on the new replacement end cap. Plastic linkage parts present the problem of breakage, so one must be careful during the disassembly process. Some other type of fasteners for the linkage assembly (screw and nut, ball and socket) would be prefereable. All and all, its a machine. Wtith exploded view, what could go wrong?
Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!
took off plate in back, plastic cover, unplugged cables, changed out board held by clips. plugged cables into new board. Plugged refrigerator back in. entered refrigerator code into door of refrigerator using temerature controls. Regrigerator started cooling. Done
I unpacked the glass and slipped it into the shelf. Done. What was more impressive was the delivery time. I ordered the glass at about 12:30pm one day and the glass was at my door by 9am the next morning. Even my husband was impressed with that.
