Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
"F3" error message and no oven heat
Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!
Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it easily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done
Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole. Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.
Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...
First, I turned the power off to the oven. With a screwdriver, I removed the 3 screws above and the 4 screws below the control panel. Next, gently pulled out the control panel. Three cables attached the electronic clock assembly to the bundle of cables controlling the oven. By pulling on the plastic tabs, I was able to loosen two of the cables. The other "cable" resembles a ribbon. Squeeze the black tabs on each side of the base of the ribbon connector and pull slightly. The ribbon itself then needs to be bent and gently removed from the connector (you can see two slits in the ribbon that hold it in place). Using my wrench set, I removed the four screws that held the electronic clock assembly to the control panel. Then I attached the new clock assembly, replaced the cables and ribbon cable, snapped in the control panel and secured it into place with the seven screws. It was very easy to do this.
Removed the metal panel, approx 5 screws, removed LED approx 4 screws and a few electronic connecters. very easy saved $100's vs calling a repair person
Switch off the breaker to the oven. Unscrew the 3 top and 4 bottom screws holding on the control panel cover. Unplug the 2 cables from the clock assembly (which run to the oven). Remove the 4 hex screws which attach the clock assembly to the control panel cover. Unplug the ribbon which attaches the clock assembly to the control panel cover by lifting the black tabs and sliding it out (there is not a plug on the end of the ribbon). Switch out the old clock assembly for the new one, reverse the steps to put it back together.
We were selling our house and the inspection report noted that the Clock on the double oven didn't work and needed to be repaired. I called the service company to get an estimate. They said $536.00 for replacing the Clock Assembly. I went to your site, saw the schematic, found the part for under $150.00 and ordered it. It took me 10 minutes to install it. Because of you I saved nearly $400.00! Thanks for the quick and reliable service I will reccomend Parts Select.com to everyone!
Ordered part on line, part came within few days well wrapped and protected, very simple repair removed two mounting screws and two lead wires to remove burnt element, replaced with new one, wire were re-connected and the mounting screws secured the new element in place, about 20 min job.
The lower and upper circuit boards were blown do to a power surge
Shut of power to unit, removed front display panel, located lower circuit board. Removed the one screw holding existing board and installed new board, then swaped wires from damaged to new. re-installed front panel, turned pwoer back on, that was it. The unit is working well.
Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.
Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.
Top oven element works, but bottom element works only intermittently
Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.
After doing an oven self clean cycle, oven temp couldnt be set correctly, heat element was warm,not hot
After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!