Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broiler element would not heat up.
not to offend anybody but what i learned on prior posts helped alot.. 1. remove unit and unplug. 2. remove door by opening to 45 degree angle and lifting door face towards you. 3. remove back panel to unit.e. 4.unscrew burner element from back inside of oven. 5.gently pry clip off each off burner element from rear of unit. Pull gently towards you. 6.unscrew support from inside oven. 7. remove old element and just reverse directions to reinstall.
Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sleeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm. Removed each wire connection individually, one at a time, installing it in the proper position on the new switch. Reverse all procedures to put things back together. A very simple, straight-forward operation.
It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.
I viewed the YTube Video that showed exactly how to remove the door and all the other parts for replacement. Excellent video shows and explains how to remove, replace, and re-attach the handle and the door.
turn off all electric to the wall oven. removed the old broiler. replaced the new broiler and turned on the electric. checked the brolier one to see if it worked....it did thanks for the customer service for her help in finding the replacement part.
Burnner would go to high setting no matter what the setting was.
Shut off power at breaker box , pull stove away from wall , remove Phillips screws from back of range pull knob off of switch . Look to see how switch is oriented remove 2 screws that hold switch in . Remove one set of wires at a time and place on new switch in same location . Put back together in reverse order .
Turn off breaker in electric panel fore stove. Put screw driver into slots in front of glass top surface. Pry top up carefully until top pops up.Remove burner dial, remove two philips head screws holding switch. Lift top carefully and prop up.With new switch close remove wires from old switch one at a time and place on new switch. Place new switch back in place, securing with philips screws. Remove prop and carefully press top down until it snappes into place.Replace dial, turn breaker back on and try burner.
1. OPEN THE OVEN DOOR TO THE FIRST STOP, PULL UPWARD TO REMOVE, ( IT WILL LIFT RIGHT OFF) 2. LAY OVEN DOOR ON A FLAT SURFACE ( HANDLE DOWN AND HANGING OFF SURFACE) WITH A TOWEL TO PROTECT THE GLASS. 3. REMOVE ALL SCREWS AROUND THE PERIMETER OF THE DOOR.. 4. CAREFULLY SEPARATE THE DOOR FRONT AND BOTTOM BRACKET BY SLIDING AWAY FROM THE MAIN DOOR INNER-ASSEMBLY, ( THE FRONT GLASS IS HELD BY THE TOP CHANNEL. 5. TURN THE MAIN DOOR INNER ASSEMBLY OVER AND REMOVE THE HANDLE ASSEMBLY TWO ATTACHING BRACKETS. 6. REMOVE THE ATTACHING BRACKETS FROM THE HANDLE AND ATTACH TO THE NEW HANDLE. 7. THE DOOR GLASSES CAN NOW BE CLEANED 8. ATTACH THE NEW HANDLE ASSEMBLY 9. REASSEMBLE IN REVERSE ORDER. ( BE CAREFUL WHEN SLIDING FRONT DOOR GLASS INTO THE TOP DOOR CHANNEL}
Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.
My 4 year old son managed to break the oven door glass. The repair man asked for $175 to fix it I had ordered the door kit from Part Select and it arrived earlier than promised. Fifteen minutes later I had it in place. The cost $49.64 Thanks Part Select,
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.
The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.