Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Shattered inside glass when attempted to self-clean
Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.
The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine. Mike
Unplug appliance, unscrew small cover plate in rear. Disconnect wires from old element, may need to use needle nose pliers to wiggle clips off. Open oven door, remove false bottom to expose baking element. Remove baking element. Install new element, connect wires from rear, and replace covers and false bottom. Plug in appliance and test.
Oven erratic, not heating correctly, timer beeper sounding
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
Removed 3 Phillips head screws at top of oven door. Tipped this top casing back just enough to remove glass door panel. Removed door mounting brackets from door (phillips). Removed end of handle from attached end of frame piece. New handle screw stubs changed from original to need self tapping screws (with washers), so had to find appropriate screws on my own (screws sent to me for new handle were straight machine screws as needed with original, broken handle). Found self tapping screws and washers, screwed new handle to brackets, screwed brackets to door panel, loosely screwed 3 top frame screws, tipped top frame back enough to reinstall glass door front, screwed down 3 top frame screws and it was done.
First things first...Unplug the unit...Then remove the center plate from the back of the oven (one screw) and take clips off element. Then on the inside, there are 2 screws near the back on the bottom panel. These were rusted on pretty good, so that's where the vice grips came into play. The entire job would've gone much faster, if I wasn't fighting with these 2 screws...After you remove the screws, tilt up bottom panel and remove. Then you just remove 1 rear screw & 2 bottom screws and slide out the old element. Slide the new one in, secure it with the screws and screw the bottom panel back into place. Go to the rear of the oven, slide the 2 clips on the element and screw rear plate back on. Plug the oven back in and that's it...
Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.
It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole. TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.
Watched Many videos to troubleshoot problem. Ordered control board and the OEM part arrived in two days. Four screws later the board was replaced and oven worked again.
left cover for the oven light broke when trying to replace the bulb
Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.
