Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The fan wheel had a blade break off, my bad.
I went on the site and found the part I needed and then watched the video explaining how to dismantle, replace the part, and put the dryer back together. It was easy, especially with the video instructions.
Bulb worked for a couple days and has now burned out, filaments dangling
To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.
I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
Dryer kept throwing the E1 error indicating the thermistor needed replacement
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
The door catch on our Whirlpool Dryer had given out.
The repair cost us less than $9.00 and about 1 minute to repair. You can only imagine how much a tech would have charged us!! We are so very happy that we discovered this site . The instruction video they offered, the customer service via their website AND quick delivery of the part, has insured them that we will be repeat customers. Thanks so much !!!!! Bravo! Annie & Peter in , Nevada
I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.
Door catch on dryer stopped catching (meaning the door would not stay closed)
I placed the putty knife on the top part of the door catch and when that came loose I placed the putty knife on the bottom of the door catch and pushed on the putty knife and the door catch came out of its place. I then just popped the new door catch in place. Total repair time 45 seconds. The door now closes.
Used screwdriver to remove old catch as shown via video from manufacture and snapped in new catch. Very easy to do and saved big bucks by doing myself.
Took a screwdriver and bent wings out a little and then was able to get hold of it with a pair of pliers. Then just put the new unit in the opening and tapped it in. If I had a good pair of needle pliers, it would not have been necessary for the screwdriver.
