Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No heat.
As others have described in more detail... I lifted the top, removed the 2 screws holding the front panel (one on each side, inside the control panel on either side - not the easiest to get at, but not too bad), popped the clips holding the front panel in place and removed it. With the front panel off, the location of the coils is obvious (lower left side). The only challenging aspect of this repair is that the 2 screws holding the coils in place are really torqued in so it was crucial to use the exactly correct size screwdriver and not let the screwdriver slip while unscrewing those screws. Actually swapping out the coils took seconds, of course they have to go in exactly the same way as the old ones. I did take a few minutes extra to vacuum out years of lint from the inside of the dryer. Overall, much easier and cheaper than I was expecting and now I know where everything is inside the cabinet.
Dryer squeak during tumbling, worn front drum glide
Disconnected power cord; lifted top using putty knife to open spring holds on the sides of the top; released front panel by removing screw from each side;removed old glide and glue; glued new piece in place; reconnected all parts and let dry overnight.
A caution to take care of sharp/rough edges when removing old felt and glide. Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.
Fit of new glide was straightforward and fit well to the lower felt glide..
(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)
Dryer making horrible squeaking sound when running
I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.
Dryer was snagging clothes between the drum and frame
Open the top of the dryer. Reach inside and remove 2 screws that hold the front in place. Detach the power cord inside where there is a connector. Remove the front of the dryer. That exposed the drum glide where all three nylon guides had worn off.
Peel off the old guide. Clean the surface with sandpaper. Use the supplied adhesive to glue on the new guide. Use masking tape to hold it while it dried.
Clothing was getting caught between drum and front panel
First unplugged the dryer took off the top. Removed the 2 screws holding the front panel on. Scraped and cleaned old drum glide and lower basket seal. glued new seals on replaced lightbulb while I had it apart then reassembled. It was an easy job and the wife is now happy again.. Thanks to Partselect. Mike
clothes getting caught on top left of drum leaving brown stains
disconnected power unlocked both top sides ,lift top back and take top 2 screws out, then unhooked wiring,then remove whole front away from drum.scrap off all the remaining pieces, then glue and wait till tacky, then apply front lower basket seal and top drum glide seal,replace the front ,hook wires back to proper place , put the two top screw back on!!! happy drying!!!
I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you
there are several srcews to remove. there are some u dont have to take out but it looks like u do.ease of the front panel and remove the old drum glide,very hard to get of all the felt.check the the bottom guide before u order parts if possible(i could've replaced mine,but didnt have time to check it first).when glue back in place follow directions exact and clamp.allow glue to dry as long as u can. mine set overnight it was nice and dry(if u dont you'll be doing it all over again)replace everything as you took them off.all works great perfect fit!!
This was a simple repair. Before I ordered the parts I had read several of the "repair stories" on this site, plus my neighbor explained to me the process. So I had a good idea of what I was getting into.
I am not real sure how long it took because I was watching a football game while I was making the repair, but I would guess if I did it straight through it would be about 1 hr.
Replacing the Drum Glide and Lower Basket Seal 1) Pulled dryer out from the wall 2) Unplugged Dryer 3) Pop the top off the dryer. Insert a screw driver in the crack right at the corners to pry the top off. 4) My dryer had a quick connector for all the wiring (which I found half way through the repair) that allowed me to disconnect all the wires leading to the door. If you can find that disconnect that so you can easily remove the door & front panel. 5) Removed two screws holding the front panel on. 6) Remove the front panel. Once the 2 screws are removed the only thing holding my front panel on were a couple of clips. 7) Removed the Drum Glide (top) & Lower Basket Seal (bottom) around the door frame in the front panel. This is the worst part because you have to scrape a lot of the glue and it takes a little while to do this. 8) Glue the Drum Glide. I used some spring clamps to hold it in place. Glue did come with the Drum Glide (but not the Lower Basket Seal) 9) Glue the Lower Basket Seal. Since I only had 4 spring clamps I waited until the Drum Glide was secure. So if you have several of these clamps that would be best. ** if not replacing the belt skip that section.
Replacing Dryer Drum Belt I took a lot of the people's advise and replaced the belt while I had the dryer apart. But if you are only replacing the belt perform steps 1 - 6 above first. 1) Remove the access panel on the back of the dryer. Mine had for screws. 2) Remove the belt. There is a spring loaded pulley that you just move to one side so the belt will loosen up enough to remove. 3) Place the new belt on. I started in the front and moved the belt over the drum to the back. Then moved to the back of the dryer and through the access panel placed the belt over the pulleys.
Thats pretty much it. I barely got dirty. Oh, while I was in there I cleaned as much lint as I could. That was the dirty part. Now all you have to do is put it back together. 1) Reconnect the front panel, and wire harness. 2) Plug it back in.
If you are wondering why I didn't replace the bearing, I didn't have any grease and the part fit but didn't look exactly like the current one. And the current one looked ok. Since this was my first attempt at fixing a dryer; I decided not to press my luck.
First I unplugged the dryer. Then I gently pryed the top of the dryer. This was done from the front using a flat screw driver. Do this gently pushing up on the handle of the tool. It will pop up one side at a time. No need to remove the screws and clips on the the rear top of the dryer. Set the top aside. Then from the inside front of the dryer using a phillips screw driver I removed two screws, one on each side. This allowed me to lift the front of the dryer up and away from the unit, off the two clips on the bottom front of the unit. I set the front cover on top of the dryer. There is no need to disconnect any wires. Next removed the rear vented cover on the back of the dryer so I could acess the belt pullies. From here I pushed the upper left pully to the right to ease belt tension and take the belt off that pully. Slide the belt to the rear of the drum. Next I removed the three screws from the center most part of the inside of the dryer drum. My dryer required the use of a square head driver tool. This allowed me to easily bring the dryer drum out the front of the unit. Set it out of your way. Then I vacuumed the dust out of the dryer. Then I lifted out the metal part that resembles a trailer hitch which had been attached to the dryer drum. Next using a nut driver I removed the two screws which hold the white plastic part of the bearing assembly to the rear of the dryer. That is all the taking apart work. Putting it all back together was not too difficult. First install the new white plastic part of the bearing assmbly inside the dryer along with the metal part on the outside rear. The little metal ball bearing goes on the OUTSIDE between the little metal part and the rear wall of the dryer. Do not leave it out as it provides electrical grounding between the dryer drum and the body of the dryer. Next attach the new bearing part that looks like a trailer hitch to the rear of the dryer drum. This is the three screw part. Then lift the drum back into the dryer. Do not yet set the drum all the way in. The dryer belt must be looped around the drum. I installed a new belt. If the bearing is worn out it is time for a new belt. The smooth side of the belt goes against the dryer drum. Now apply a generous amout of lubricant to the white plastic cradle which was installed on the back of the dryer and to the ball bearing area. Then the dryer drum may be set into place, that is the trailer hitch part into the white plastic cradle. Now the front of the dryer may be reinstalled. Push up on the inside of the dryer drum to line everything back up. Put the two screws back which hold the dryer front on. Be carefull not to drop them inside. Put the dryer belt back into place on its pullies. It goes on the inside of the left and right pullies and on the outside (bottom) of the pully of the dryer motor. Check for and undo any twists. Plug in and test the dryer. All should be well. Reinstall the rear vented cover. Replace the top, connecting the rear first. Make sure to reattach the green grounding wire. Then push the front of the top down onto its clips. You are done! This took me 1 hour and 10 minutes. It sounds like alot but you can do it! Empower yourself!