I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.
Make sure to unplug the power cord.Pry the front,top of the dryer up with a screw driver. Carefully disconnect 3 wires and remember where they go, top right. Remove 1 top bolt on each side of the front cover, inside.Pull up slightly and towards towards you to remove the front cover. Disconnect the light wires if applicable and remember where they go from the front drum support. Remove 4 bolts on the front drum mount cover; the lint catcher will come off with it. If needed, pull up and towards you on the drum to lower the it off of the guide rollers to allow slack in the belt. Reach under the drum, raise the idler lever, slide belt from under the idler lever pulley, remove the belt from the the motor shaft. Carefully remove the drum. A 7/16 wrench and ratchet can be used to remove the idler lever from the mount. Remove idler lever from the spring. Reverse these steps for installation of the new idler lever. For installing the belt, actually fold the belt and put it under the idler pulley and back onto the motor shaft. The idler lever should sit on top of the belt when on properly. Make sure the belt is lined with the wear area of the dryer drum. Roll the drum manually, counter clockwise several times to help insure belt alignment before reconnecting the wires and re-installing the front cover and top. A belt replacement will not require removal of the drum.
After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!
Screaching on start-up, then continuous after time
Idler was the noise source. Drum support rollers were failing also. I almost spent $500.00 on a new dryer, glad I replaced the parts instead. Sounds and works like new. Watch the video,its very helpful. Thanks Parts Select. You should advertise your services on TV or radio. I am glad I found you.
Researched problem on line. Many others had same symptums after power outages and Hurricane Irene. Dryer was in use when power went off, back on, back off than on again. Dryer would not work more than a few seconds. LED lights would go off; Drum did spin; Heater elements came on. All symptoms pointed to the control board. Replaced board and dryer is working now. Reports state that this particular control board is very susceptable to power bumps and will fail.
discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!
Screeching dryer followed by later clunking when roller went
I pretty much followed a lot of the earlier postings on partselect.com that provided encouragement to pursue replacing this part on my 17 year old dryer (sorry, money is tight these days and I prefer repair to $800 replacement).
I'd like to add that I borrowed a pair of snap-ring pliers from work which made removal and later securing of roller onto shaft much easier and probably avoided a lot of knuckle bruising and cursing.
I erred though in a couple of places during the replacement. Disassembly took about 20 minutes. However, when I re-assembled I had mistakenly already put the roller onto the shaft before trying to put the drum back in. That isn't possible so I had to remove (an initial groan but only a few extra minutes in the end) the roller from the shaft, then reposition the drum and then the roller back on the shaft.
I also decided to replace the belt while I was in there and I should have taken a picture or made a drawing of the belt route before I took it off since I was later left pondering how the heck to snake the belt onto the shaft and also the tensioner. A quick trip to the internet though showed me a similar route and reminded me how to route it.
I'd also like to add to be cognizant of the wires on the door and front panel when disassembling.
Anyone with any sense of mechanical ability and a little common sense ought to be able to do this repiar.
top of the lint filter broke off, tearing our clothes.
Ordered the part, you made it so easy. Received it in two days, very fast, by regular mail. Perfect fit. Pulled out the old broken one and put in the new one!
Very simple repair. Remove front panel, door, drum etc. Try to keep everything seperated, screws etc. I put lockjaws on the back to get the nut off the front. Make sure to check the housing for "melted on" blower wheel residue. Easy enough to remove. I checked with my local parts dealer he wanted twice the price and needed to order it (at least a days wait). PartSelect sent the exact same part in a day and a half. Put everything back the same way I removed. Hardest part is the drum and belt. While you have everything apart don't forget to clean the thermastats etc. PartsSelect was quicker and cheaper.
How to take apart a dryer: The first way: 1) Remove front lower panel (2 screws on bottom). 2) Remove the front black plastic air duct. 3) If you have long arms, or an extention socket wrench, you might be able to reach the heating unit, otherwise use the Second way:
The second way: 1) Remove front lower panel, as this will expose the screws to the dry door unit. 2) Remove dryer door unit (2 screws on bottom, 2 spring clips on top), and disconnect assoc wires. 3) Remove dryer lid: 3.1) Remove 2 screws on front (previously hidden by door unit 3.2) Remove 2 clip hooks on back of dryer 3.3) Lift lid rear above center guides, and wiggle away from front spring clips 4) Lay dryer on back, as this will allow easier removal of the drum 5) Remove screws securing the heater control unit.
Attempt 1: Disconnected heating element and saw that the heating coils were broken. Ordered new heating coil and new belt. Attempt 2: 3 weeks after installing new heating element, my wife informed me that the unit was no longer putting out heat!!! So, I ordered the Thermostat and Thermal Fuse. Put dryer back together. Attempt 3: Turned it on - absolutely nothing - dead, dead, dead. Discussed purchasing new $600+ dryer. Started taking it apart again, and discovered that door wire was never reattached. Meaning the dryer thought the door was wide open. Attempt 4: Now the dryer squeaks. Took dryer partially apart and added white grease to wheels that support the drum. Currently, all is well with the world.
Moral of the story: Replace the entire heating unit, check belt for cracks and grease the wheels if you get a chance.
Dyer Blower went bad a dime fell in and wore it out
The repair looked simple enough until it came time to take the out wheel off. Because you can not hold the motor shaft(and the wheel screws on) it was necessary to remove the whole motor assembly and then grind the out shaft down, then use a small screwdriver to take the remaining shaft off. I must say it was nice to recieve the part in as fast as I did we live in a very rural area and things like that are very hard to find
