Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burn marks on clothes
Opened the top of the dryer (no tools needed). used socket set and removed the two screws (one on each side). unpluged wires from front panel, labled each (good practice). Pulled open the front panel. cleaned old felt off all around the front panel. Wiped down everything. while I had it opened, I vaccumed out the dryer underneath. used glue provided in felt kit and glued new felt where old was. let dry, put front panel back on ensuring that the felt was between drum and front panel. put screws back in front panel. closed top. Let me say that this is the third time I've done this to this dryer as it is about 18 years old. Until the heating coils go out, this is the cheapest fix there is. :-)
Clothes caught between drum and felt, leaving stains
First, I popped the two clips that hold on the top. Then, I removed two screws and unplugged a few wire connectors to remove the front panel. I scraped off the felt, which was rubbing the drum since the white plastic glides had worn completely through. I applied the high-temp adhesive liberally, laid on the new felt, and applied some spring clamps to hold it in place. I removed the small back panel to replace the belt, which was really easy with the dryer apart. The 7-year-old original belt was a little cracked.
First I raised the top of dryer, then removed 2 screws holding the front of dryer to the sides. removed old drum glide using a putty knife and glued new glide in place with glue provided. replaced front and top. The whole job took about 20 minuets and saved me the cost of new dryer
First of all, I LOVE Partselect.com.. The parts are reasonable, and arrive in a timely fashion.. The repair stories are far and away, one of the BEST features of this website - so hats off to the DIY'ers who have helped me overcome my challenges and helped me stay in the ..ahem.. "favorable" graces of my wife.. I need all the help I can get there.. Anyway, read the other repair stories first - LOTS of great insight.. I only have a couple pointers to add - below...
This is easily my 4th appliance repair project with Partselect.com, and I can say without a doubt that the experience has been positive every single time.. Until now.. I got the dryer torn down and realized that I SHOULD have ordered the SEAL-BASKET LOWER felt with my original order. When I inspected it for my list of parts to order, the upper glide was thrashed - no brainer.. I thought the lower felt was fine.. d'oh! I discovered this morning that I was wrong.. So, I JUST ordered the lower basket seal for *next* weekend.. (If you are gonna replace the original upper glide, replace the lower basket seal as well..) It'll be a slam dunk, though..
Now, for a couple useful tips:
If you are a car guy, get out your trusty can of brake parts cleaner to help clean off the old adhesive residue after you rip off the old upper glide felt. I also used a 1" plastic scraper to help facilitate removal, but the brake parts cleaner was a Godsend. I think I read someone else's suggestion to use "goof off" or whatever - but I couldn't find mine, so..... ...out came the brake cleaner... :) two thumbs up. Just use it sparingly - all those solvents are bad for children in California for some odd reason..
Spring loaded clamps to hold the felt down as the glue dries are also "nice to have". I used one on each end of the felt, and one for each of the teflon / plastic glides..
Finally - milk this job for all it's worth - it'll only take you 45-60 minutes or so... good luck...!!!
took off face of dryer, removed drum 4 screws removed two srews holding bearing and shaft ,replaced shaft bearing and shaft . Just for preventive maintenance i replaced idleling arm and dryer belt. I lined everything up replaced drum used shop vac to clean lint and dust from all parts replaced face of dryer and boom i got a btand new dryer
I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you
Had a squelch/squeak coming from the rear of the unit
I looked up a YouTube video on my specific model. Found one that said “basic disassembly”. I watched that and had it apart and back together in no time. Very easy to take apart and put new parts back in it. Re-assembled and since the repair no squeaking.
May not have to take out the whole drum to replace the limiter!
After lifting the dryer top and finding the location of the thermal limiter on the back of the dryer, where it is difficult to get at, I carefully cut through the dryer cabinet with the multimaster on three sides to form a 'flap' upon which the limiter was mounted. By prying this flap open from the back, the two wires and two screws are easily accessible to replace the limiter, without having to remove the whole drum. Afterwards, I just bent the flap back into place and taped the seams. If it ever blows again, the fix will take all of about two minutes.
I basically followed the video instructions on your website. Pretty simple but ran into an issue pre-threading the 3 self taping screws into the spindle bearing. The screws provided were blunt on the end and did not tap easily at all. I used the existing screws that were much more "sharp" and worked much better. Also, the new screws were Philips drive and due to the amount of torque trying to self tap nearly stripped them out. The old sharper screws were square drive which had a better bite. So basically, I used the old screws to self tap and then used the new screws for the final installation. It took a long time to clean all the lint out from the inside of the dryer. The motor was completely embedded with lint and animal hair. You may want to suggest that a good cleaning may be needed so bring a shop vac...and also something to carefully pick the lint balls out from around the motor armature and bearing area. Overall the video instructions were really a big help!
Unplugged the dryer, removed the top of, disconnected the electrical connectors, removed the front panel, disconnected the belt, removed the drum, removed the old Safety Thermostat, installed the new Safety Thermostat and assembled the dryer again.