Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
22 year old dryer making rumbling noise
This dryer has been really reliable. This is the first time I've had to repair it. PartsSelect.com says the noise had a 30% chance the problem would be the tumbler rollers and shaft and 18% it would be the blower impeller fan. I took a chance on the rollers, thinking I would save $20 on the blower fan. Big mistake! Once I dissambled the dryer, I realized almost immediately it was the blower fan and not the rollers. When I manually turned the motor shaft, I discovered the problem. The plastic fan's shaft hole is worn to a larger diameter and is semi-freewheeling on the shaft causing the racket. I replaced the rollers and belt and ordered a new fan. I tried putting electrical tape on the shaft to enlarged the OD like a fellow on this site said, but it worked for about 3 minutes then the racket started again. Also, I had to pull the dryer away from the wall and open the access door to the back of the motor in order to thread the drive belt on the motor and idler pulleys. I couldn't fit my arms along side and under the tumbler. I've got the scratches on my left arm to prove it. Suggestion: Replace the blower fan, rollers and shafts if you have the rumbling noise when operating the dryer. Might as well replace the drive belt while you have it apart, too.
low noise from worn blower and rollers and pulley worn
Fast receipt of parts from supplier . All parts went together very quickly. Don/t recommend this work for those who have no mechanical skills. realignment of screws can be very tricky . They must all be correctly aligned first and driven in at diagonals to equalize pressure . Job needs to be used with hand tools as it is easy to strip out the threads in dryer by overtightening the screws. PS before this we had replaced the drum belt. Update: We ran the dryer after replacing the drum support rollers and the idler pulley and it was smooth for about 5 minutes. then the rumbling and uneven rotation started up again! The tip-off was when we had done a test roll on the drum after changing the above parts, we heard a rumble from the blower wheel! so we ordered the blower wheel, replaced it and the dryer sounds like new. Thanks to others who have written their stories which helped us figure out the problem. : ) saves big $$ on buying a new dryer. PS ours is 15 years old and has had heavy use.
Remove the door and the plastic brackets on the other side of the door opening. Remove the front cover by gentally pulling from the top first. Support the dryer basket (I used an old towel and a block of wood. With a 1/2 inch wrench remove the Roller Shaft with the Drum Support still attached. Replace new shaft and drum support. (always replace both at the same time or you will find that the problem will come back much sooner.) Careful when installing. Make sure that the new non metalic washers (suppied) are propery seated when you are tightening down the nut.
After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!
discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!
replace tumbler/motor belt and drum support rollers
Tip: If the belt broke make sure the Drum Rollers are not seized which could have broken the belt. I recommend if replacing the belt replace the Drum Rollers (2- required) at the same time. The instruction sheet that came with the Drum Roller kit is straight forward. It provided detail on what to disassemble to replace the rollers. So follow the instructions. Tip: Make sure you have a C – clip ring pliers to remove the C clip. The instruction sheet calls it the snap ring The Idler Pulley came with no instructions, however it was easy to replace. The idler pulley is secured with an “E” shape clip which can be removed with a small straight blade screw driver. The instruction sheet on how to install the belt was good showing how the belt is routed. The instruction wants the belt installed from the front around the tumbler then from underneath the tumbler towards the back and around the motor pulley and idler pulley. It is hard to see the motor and idler pulleys from underneath the tumbler. However I think it was easier if the tumbler was moved forward enough so you can see the motor and idler pulleys from the top. Install the belt as shown in the instruction sheet diagram around the motor pulley with the groves of the belt are against the pulley, then around the idler pulley. While holding the belt with slight tension, move the tumbler back into position while routing the belt around the tumbler and slowly turning the tumbler until the belt is completely installed. The belt should be about 1-1/2” from the back screws which hold the tumbler baffles. Note: the belt should be installed with the flat side against the tumbler. The belt should not be in the back grove of the tumbler.
actually used the videos available on your website and it made the job really simple other than the fact that I live in Florida and it was 96 degrees and my dryer is in my non-air conditioned garage.
Problem was the blower wheel, (Plastic deteriorated). Replaced the tumbler and motor belt as well as th idler pulley. While the blower wheel turned out to be the problem, the other parts were significantly deteriorated. Since I had the dryer disassembled it made sense to replace the other parts. The 24 year old dryer runs like new. The parts select instructional videos were extremely helpful.
Barrel of dryer would not turn due to a broken belt.
Removed the front casing of the dryer. loosened the barrel of the dryer, threaded the belt (per instructiond given inclosed with belt) replaced screws, casing and reconnected wiring. All went well and when connected to electricity and started, dryer ran fine. Thank you for the instruction sheet, there could have been trouble re-threading if the sheet had not been enclosed. I am a satisvied customer! !
took the front cover off the dryer to get front access to the tumbler and the rear access panel to get access to actually aligning the belt on the tumbler. all in all it was fairly simple to change and the part came in within 2 days of ordering. very pleased with the delivery time!!! thanks, jason hines
From the sound it made I thought it was the rear rollers. That happened once before on another dryer. After removing all the parts I foung out they were fine. First unplug the dryer: Then remove the dryer front door panel. 2 screws at the bottom of the door. Lift cover from the bottom of the door, it is kind of on a top hinge. On the bottom left hand corner you will see the plastic cover for the blower. It has 6 small screws that hold the cover on. Once the cover is off you will see the blower wheel. Use a pair of Snap Ring Pliers to remove snap ring at end of the shaft. Use a pair of needle nose pliers to remove the clamp around the blower wheel that holds it onto the shaft. Slip off the old part. That was the rumbling noise.
Firts I had to take all the front parts off using a screwdriver and nutdriver then I loossen the belt to get the drum out then I had to use snapping ring pliers to remove the rollers and put the new ones in I cleaned the inside of the dryer then I put everything back in place. After all that I tested it and it worked really good it took me about an hour to do all that
