Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Very simple just remove the rakes and then unscrew the covers and pop out the old chopper assembly and replace with the new and then just put all cover back and it works great.
Dishwasher would not drain. Pump was jammed with broken glass .
Turn off breaker to dishwasher. Remove lower basket. Drain any water using a wet vac. Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver. Should be able to reach pump. Turn counter clockwise to remove. Disconnect plug wire on pump. Install new pump by turning clock wise. Reattach wire plug. Run a wash cycle with empty dishwasher and check for leaks. Replace cover plate. Done.
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
1) Pull out dishwasher from under counter. 2) Disconnect spring located at the bottom on each side of dishwasher. 3) Using socket remove pulley wheels from each side at bottom. 4) Install new pulleys on each side. 5) Wind pulley cord around both wheels and attach to one end of the spring on each side. 6) Using pliers extend other spring end to lower frame of dishwasher on each side. 7) Open and close dishwasher door to test. 8) Replacement complete
top rack quick washing water was not spinning throught top
checked all the plactic tubes for clogs used water hose and they worked ok checked into top of pump found chopper assembly had come apart replaced washes like a new one
removed the upper and lower baskets, removed the lower wash arm by rotating the center bearing assembly (its the flat piece in the very center of the lower wash arm) by the way it has a reverse thread...not righty tighty and lefty loosey... it is reverse the normal rotation.. i unlocked the upper arm assembly from it's clip on to mount as well as the clip on to mount on the back wall, looking at the very center pump cover strainer, you will see that the assembly that goes from the pump area to the very top of the machine needs to be rotated clock wise where it locks into the pump strainer assembly. now remove the four star type screws from the face of the strainer, now you can lift out the entire bottom of the machine you will see the half round cover in the bottom of the well, remove one smaller size star screw. simply remove the chopper assembly and install the new assembly as indicated in the instructions provided, be sure to use the trick with the open end wrench as per instruction sheet, makes it easy. now follow the bread crumbs you left on the yellow brick road to reassemble.
After several weeks of decreasingly clean dishes on the top rack of our dishwasher, I did some digging & found that my chopper assembly was broken (the washer had come off & the parts were loose). I ordered a new chopper assembly here. Once I received it, the entire repair took less than 30 minutes. I removed the old chopper assembly, used a shop vac to remove the excess water & food particles, then reinstalled the new chopper assembly using the instructional video provided. The dishwasher is back up & running like brand new. The top rack is getting cleaned thoroughly once again. PartSelect made the process extremely easy & affordable!
These wheel assembly that came on the lower rack of my dishwasher were junk! They started falling off within 6 months. I put them back on to the point that the pin in the center of the wheels would no long stay in place, thus the frustrating situation of the wheels falling off often.
Very easy. I removed the two screws on the base plate, then the two screws that attach the washer to the cabinet, and pulled the washer out of its slot. I installed the broken side and closely checked the other side and felt it didn't need repairing. I put it back together and the door works very well.
