Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher door leaking
Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.
Order both this seal and the seal for the bottom of the door at the same time.
Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.
no power to control panel. Lights would not come on when button is pushed.
Take pictures of electronic control with phone. Has multiple connections. Slide elect. cntrl. off mount swap connections 1 at a time to new cntrl. Slide new cntl. on mount. Connect control panel. Re-install inner panel. Be sure to disconnect power plug before starting. Good luck
First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.
The dishwasher is has been in service only 18 months and the seal between the motor and pump leaked, destroying the front motor bearing.
Rather than just replacing the motor and seal, I figured it would be just as easy to replace the sump and pump assembly also. It makes sense because the extra cost is minimal and I have a completely new unit now. The repair is quite simple. Just three clips holding the sump and a few electrical connectors and the unit comes right out.
The handle was broken which we noticed when we had replaced the front panel.
Turn off the power to the dishwasher by turning off the breaker at the breaker panel.
Unscrew the inside door panel using a star screw driver. Unscrew the broken plastic handle and replace with the new part. Screw the door panel back on.
Very simple just remove the rakes and then unscrew the covers and pop out the old chopper assembly and replace with the new and then just put all cover back and it works great.
Dishwasher would not drain. Pump was jammed with broken glass .
Turn off breaker to dishwasher. Remove lower basket. Drain any water using a wet vac. Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver. Should be able to reach pump. Turn counter clockwise to remove. Disconnect plug wire on pump. Install new pump by turning clock wise. Reattach wire plug. Run a wash cycle with empty dishwasher and check for leaks. Replace cover plate. Done.
removed the upper and lower baskets, removed the lower wash arm by rotating the center bearing assembly (its the flat piece in the very center of the lower wash arm) by the way it has a reverse thread...not righty tighty and lefty loosey... it is reverse the normal rotation.. i unlocked the upper arm assembly from it's clip on to mount as well as the clip on to mount on the back wall, looking at the very center pump cover strainer, you will see that the assembly that goes from the pump area to the very top of the machine needs to be rotated clock wise where it locks into the pump strainer assembly. now remove the four star type screws from the face of the strainer, now you can lift out the entire bottom of the machine you will see the half round cover in the bottom of the well, remove one smaller size star screw. simply remove the chopper assembly and install the new assembly as indicated in the instructions provided, be sure to use the trick with the open end wrench as per instruction sheet, makes it easy. now follow the bread crumbs you left on the yellow brick road to reassemble.
top rack quick washing water was not spinning throught top
checked all the plactic tubes for clogs used water hose and they worked ok checked into top of pump found chopper assembly had come apart replaced washes like a new one
